ShoreLand'r PWC1000-8 - Manual

PWC1000-8, PWCG1000-8 & PWCBK1000-8
Parts Manual
PWC1000-8 Single PWC W/8” Tire - 1000 - White
2 4300179 18.5X8.5X8B Tire/MSilver Mod Rim
1 62340 Literature Bag - Trailers
1 6417901 Frame Bundle - PWC1000-8 Wht
Tire Size &
Carrying Capacity Chart
Tire Load Carrying
Size Range Capacity
18.5X8.5X8 B 770 lbs. per/tire
Refer to tire side wall for correct tire pressure.
Tongue Weight Adjustment
Slide the water vehicle either forward or backward on the
trailer until the proper tongue weight has been achieved.
PWCG1000-8 Single PWC W/8” Tire - 1000 - Galv.
2 4300201 18.5X8.5X8B Tire/Galv. Mod Rim
1 62340 Literature Bag - Trailers
1 6417901 Frame Bundle- PWC1000-8 Galv.
PWCBK1000-8 Single PWC W/8” Tire - 1000 - Black
2 4300179 18.5X8.5X8B Tire/MSilver Mod Rim
1 62340 Literature Bag - Trailers
1 6417903 Frame Bundle-PWC1000-8 - Black
Final Assembly Instructions
Remove all small parts from the frame by cutting the
bands. Remove the bolt bag and sort all nuts and bolts by
size.
Tongue:
Remove the tongue assembly from the frame bundle and
slide into the tongue channel. Secure with a 3/8” X 4”
carriage bolt in the front and 3/8” X 3-7/16” X 4-1/8” square
u-bolt, 1” X 4-1/2” mounting strap (Ref.#60) and 3/8”
flange lock nut in the rear of the assembly. Thread the
tongue wire harness through the tongue and connect to
the frame harness and install the grommets. NOTE: Install
the tongue in one of the two adjustment holes in the
tongue channel. Refer to the parts drawing for placement.
Safety Chain:
Insert a 3/8” X 1-1/4” hex bolt with a 3/8” flat washer and
safety chain through the lower hole on the front of the
tongue. Secure with a 3/8” flat washer and 3/8” flange lock
nut. Repeat this procedure on the opposite side of the
tongue.
Coupler:
Mount the coupler onto the tongue with one (1) 1/2” X 4”
hex bolt and two (2) 1/2” X 1” hex bolts. Secure with 1/2”
flange lock nuts.
Winch Post:
Attach the winch brace (Ref.#53) to the winch post
assembly with a 3/8” X 4” hex bolt in one (1) of the three
(3) holes of adjustment desired. Position the winch
assembly on the tongue in the desired position and fasten
with a 3/8” X 3-7/16” X 4-1/8” square u-bolts, 1” X 4-1/2”
mounting straps (Ref.#60) and 3/8” flange lock nuts.
Axle:
Install the spring bushing (Ref.#49) in the rear spring
brackets with 1/2” X 3-1/4” hex bolts and 1/2” flange lock
nuts. Position the axle under the trailer with the spring eye
to the front. Slip the flat end of the spring in the rear spring
bracket and fasten the front spring eye to the front of the
spring bracket with 9/16” X 3-1/4” hex bolts and 9/16” hex
lock nuts.
Mount the tire and rim assemblies with 1/2” lug nuts and
tighten to 80-90 ft./lbs. of torque.
Bunk:
Slide a 3/8” X 2-7/16” X 2-3/4” square bolt over the rear
cross member with the threads facing the REAR. Place a
adjustable bunk bracket (Ref.#61) on the u-bolt legs and
secure with 3/8” flange lock nuts. Slide a 3/8” X 2-7/16” X
2-3/4” square u-bolt over the front cross member with the
threads facing the FRONT. Place a adjustable bunk
bracket (Ref.#61) on the u-bolt legs and secure with 3/8”
flange lock nuts. Fasten the bunk assembly to the
adjustable bunk brackets just mounted and secure with 3/
8” X 1” hex bolts and 3/8” flange lock nuts.
CAUTION:
To prevent damage to your water vehicle hull, place the
water vehicle on the trailer, loosen bunk u-bolts so the
bunks conform to the hull. Tighten.
To prevent damage the trailer or vehicle, tighten all
fasteners before towing.
The law requires that the white wire on both the tongue
and vehicle wire harness be grounded to the trailer and
towing vehicle.