ShoreLand'r SS1066 User Manual
Ss1066 pontoon tri-toon kit, Ss1066 material list, Ss1066 assembly instructions

SS1066
Pontoon Tri-Toon Kit
Made in the USA
Midwest Industries, Inc. Ida Grove, IA 51445 Tele: 712/364-3365
0002718
SS1066 Material List
REF# PART#
DESCRIPTION
QTY
1
0110060 3/8 X 4 HEX BOLT ..........................1
2
0110114 1/2 X 4 HEX BOLT ..........................1
3
1440101 3/8 SM FLANGE LOCK NUT ...........11
4
1440102 1/2 SM FLANGE LOCK NUT ...........17
5
62670-- TRI-TOON TONGUE 3X5X102 ........1
6
S-3179G BUNK BRACKET ..............................4
7
0140040 3/8 X 1 HEX BOLT ..........................8
8
0310228 1/2 X 3-9/16 X 4-1/4 SUB ..............4
9
0310365 1/2 X 5-9/16 X 4 SUB ....................8
10
0810930 #10-12 X 1-1/4 PHIL FLAT SCREW 8
11
1310040 1/2 S/T MED LOCK WASHER .........8
12
1440159 1/2 HEX FIN NUT ............................8
13
60047-- ADJ BUNK BRKT - HULL STABILIZ .4
14
6046200 ADJ BUNK BRACKET CLAMP .........4
15
62315
2X6X13 BUNK .................................2
16
63745-- TRI-TOON SUPPORT TUBE WLD ...2
17
S-3412 TONGUE ROLLER BRACKET .........1
18
1340105 5/8 USS FLAT WASHER .................2
19
1410221 5/8 PUSH NUT PALNUT ...............2
20
3510053 3-1/2ODX5/8ID ENDCAP ROLLER 2
21
3510155 8 KEEL ROLLER W/P&B 5/8 ID .....1
22
4272
5/8 TONGUE ROLLER PIN 11-1/8 .1
23
0210130 3/8 X 3-3/4 CARRIAGE BOLT ........2
24
64833-- SPACER TUBE FOR PONTOON .....2
SS1066 Assembly Instructions
Place one tri-toon support tube weldment (Ref.#16) on rear
of trailer just ahead of rear crossmember using 1/2 X 5-9/
16 X 4 SUBs (Ref.#9) and secure with 1/2 flange lock
nuts (Ref.#4).
Place the second tri-toon support tube weldment (Ref.#16)
approximately 90 forward from rear crossmember just
installed (see drawing for approximate placement). Leave
1/2 X 5-9/16 X 4 SUBs (Ref.#9) loose until bunks
(Ref.#15) are in place and positioned properly.
Mount hull stabilizers (Ref.#13) to support tubes using 1/2
X 3-9.16 X 4-1/4 SUBs (Ref.#8) and secure with 1/2
medium lock washers (Ref.#11) and 1/2 hex nuts
(Ref.#12). Mount bunk brackets (Ref.#6) to hull stabilizers
and tighten using 3/8 X 1 hex bolts (Ref.#7) and secure
with 3/8 flange lock nuts (Ref.#3).
Measure 22 in from rear of each 2X6X13 bunks (Ref.#15)
and secure to bunk brackets (Ref.#6) using #10-12 X 1-3/
4 phil flat screws (Ref.#10).
Adjust front support tube as needed before tightening nuts
and securing front of the bunks to bunk brackets (Ref.#6).
After assembly is complete adjust bunks up or down, or
side to side as needed to fit your tri-toon.
Remove black plastic pad from winch post extensions.
Mount the spacer tubes (Ref.#24) onto winch post exten-
sions using two 3/8 X 1 hex bolts (Ref.#7) in top and
bottom holes. Place the black plastic pad onto the spacer
tubes and secure with a 3/8 X 3-3/4 carriage bolts
(Ref.#23) and 3/8 flange lock nuts.
Refer to parts drawing for proper placement.