ShoreLand'r SLRB46TBS V.1 - Manual (Page 8)

Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorelandr.com 0003477
Page 8
ONE AXLE BRAKE INSTALLATION
Cut the tape securing the brake line hose to the axle.Remove the
brass plug from the port in the brass block on the right brake cali-
per. Thread in the brake hose male end and tighten to either 6-8 ft.
lb. or 72-96 in. lb. of torque.
DO NOT OVER TIGHTEN Over tightening will cause the brass
block to crack and then leak.
Place the other end of the hose up through the hole provided in the
brake line clip bracket. Secure in place with the U-shaped hose clip
provided.
Remove the plastic cap from the end of the frame brake line com-
ing out of the side frame by the axle. Carefully uncoil the brake line
so that it will reach the end of the hose just attached to the brake
line bracket.
Thread the brake line fitting into the brake line hose.
Tighten.
NOTE: The axle has brake fluid installed in the calipers and the
axle line when it is assembled at the factory. This is done to protect
the inner parts of the brake system during shipping and storage.
The complete brake system including the axle MUST be re-bled to
ensure that all air has been removed from the brake system.
For bleeding instructions see the UFP brake bleeding manual or
the ShoreLand’r Disc Brake Manual.
Fill the actuator reservoir with brake fluid and bleed the line per the
instructions in the Brake Manual.
TIRE & WHEEL ASSEMBLY
Mount the tire and wheel assemblies using the 1/2” fine threaded
tapered lug nuts provided. Tighten to 85-95 ft./lb. torque using the
rotation pattern as shown in the ShoreLandr’s Owners Manual.
Re-torque the lug nuts after 50 miles driving and then periodically
thereafter.
TRAILER ADJUSTMENTS
The adjustment of the trailer to your boat is very important not only
for the trailer, but also the boat. Failure to do so may lead to poten-
tial failure or damage to either the trailer or boat.
Adjust as follows:
AXLE ADJUSTMENT
The amount of tongue weight on your trailer can be adjusted as
follows:
To lower the tongue weight, adjust the axle assembly forward. To
increase the tongue weight, adjust the axle backward.
The distance that the axle assembly has to be moved will vary be-
cause it is directly related to the weight and center of gravity of the
boat placed on it.
Best towing is achieved when the tongue weight is 5-7% of the total
gross load of the complete unit.
Note: Wire harnesses and brake lines will need care when moving
the axle assembly.
REAR RB SUPPORT SYSTEM
Place the boat on the trailer so that the transom is located 1-2”
from the rear of the bunks. This gives you maximum support on
the transom.
The rear cross member is adjustable forward or backward to allow
the trailer to be adjusted to various length boats. This is accom-
plished by removing the pivot bolt that holds each end of the rear
pivot to the side frame. Reposition the rear pivot arm into the other
hole position predrilled in the side frame. Reattach the rear pivot to
the side frame with the bolts just removed. Tighten.
The wire harness for the three-light identification light must be re-
positioned where it comes from the side frame to the rear pivot to
eliminate slack, and sagging of the wiring.
Position the RB bunk assemblies so they are far enough apart to
give your boat stability while transporting. When the desired width
is achieved, move the RB bunk assemblies so that they are just to
the outside of a strake.
The RB bunk assemblies need to be adjusted so that you have a
minimum of one to two inches of clearance between the keel of the
boat and the center cross member pads. This will help center the
boat when loading and unloading.
When the desired position is determined, tighten only
enough to hold the bunks from moving while the other adjustments
are being made. Final tightening will be done at the end of the ad-
justing process.
FRONT ROLLER SUPPORT SYSTEM
The keel of the boat must rest on the center of the front keel roller
system creating a three-point support system. The keel roller sys-
tem is designed to fit most boats without needing any further ad-
justment. It is a rare occasion when the front roller cradles will have
to be raised. However, due to variances in boat bottoms, the need
may arise that you may need to raise the roller cradle higher to sup-
port the boat properly.
This is accomplished by adding an optional SS1003 riser bracket
that will raise the front roller cradle assembly ¾”. A second kit can
be added to raise the roller system a total of 1 ½”.
Once the height of the roller cradle assembly is established the
stabilizer pads can be adjusted. This is accomplished by sliding the
pad up against the boat bottom by hand. It is not necessary that
they carry much weight. They are designed to just give your boat
added stability while being towed. It may be necessary to adjust
the assembly up so that they can be moved further apart giving ad-
ditional support. Pull the assembly away from the boat. Place the
U-bolt that holds the assembly to the cross member in a lower hole
in the bracket. Then push the assembly back against the boat.
Tighten in position.