beautypg.com

ShoreLand'r SLBR58TBB User Manual

Tire size & carrying capacity chart, Tongue weight adjustment

background image

®

SLB58TBB & SLR58TBB Parts Manual

Final Assembly Instructions

SLB58TBB

3X5 Bunk Trailer - 5800 lbs.

4 4300199 ST215/75R-14C Tire/MSilver Dir Rim (or)

4 4300198 ST215/75R-14C Tire/Galv. Dir Rim

2 T-781B

Axle Assembly - 3X5 Tandem W/Brakes

1 S-3319

3X4X81” Tongue W/27-1/2” Hitch - White

1 4510270 Dico 7,500 lb. Actuator

4 61778--

36” Bunk Assembly W/Brackets

1 62469--

Frame Bundle - 3X5 - SLB/R58TBB

1 62340

Literature Bag - Trailers

1 62466--

Support Tube Assembly for 3X5

1 62467

Brakeline Kit - 1st Axle - 3X5

1 62468

Brakeline Kit - 2nd Axle - 3X5

Tire Size & Carrying

Capacity Chart

Tire

Load

Carrying

Size Range

Capacity

ST215/75R-14

C 1870 lb. per/tire

Refer to tire side wall for proper tire pressure.

Tongue Weight Adjustment

Approximate Tongue Weight for Best Towing.

Tongue weight too high, move the axle assembly forward.

Tongue weight too low, move the axle assembly backward.

Tongue weight should be 5% to 7% of the total gross

weight of the boat and trailer combined.

SLR58TBB

3X5 Bunk Trailer - 5800 lbs.

4 4300199 ST215/75R-14C Tire/MSilver Dir Rim (or)

4 4300198 ST215/75R-14C Tire/Galv. Dir Rim

2 T-781B

Axle Assembly - 3X5 Tandem W/Brakes

1 S-3319

3X4X81” Tongue W/27-1/2” Hitch - White

1 4510270 Dico 7,500 lb. Actuator

4 60617--

24-1/2” Roller Arm Assembly

1 62469--

Frame Bundle - 3X5 - SLB/R58TBB

1 62340

Literature Bag - Trailers

1 62466--

Support Tube Assembly for 3X5

1 62467

Brakeline Kit - 1st Axle - 3X5

1 62468

Brakeline Kit - 2nd Axle - 3X5

Remove the small parts from the frame by cutting the bands.

Remove the bolt bag and sort all nuts and bolts by size.

Rocker Bogie:

Align the center hole of the rocker (6239210) with the center hole

of the spring bracket. Insert and secure with a 3/4” X 4-1/2” hex

bolt from the outside-in and tighten with a 3/4” hex lock nut.

Springs:

Mount the springs to the axle with the 1/2” X 6-1/2” axle u-bolts

from the top down. Install the 4” spring clamp on the top of the

spring under the u-bolts. Install the spring plate under the axle.

Tighten the 1/2” flange lock nuts evenly.

Axles:

Fasten the springs to the axles with the 1/2” X 6” axle u-bolts,

spring plate and 1/2” flange lock nuts. Note: Make certain the

hook end of the springs point in the same direction to the rear of

the trailer, on both axles! For the rear spring and axle - place a S-

3207G, galvanized spring bracket bushing, in the rear of the

spring bracket. Insert the 9/16” X 3-1/4” hex bolt through the

bracket from the outside-in and tighten with a 9/16” hex lock nut.

Slide the end of the hook spring over the bushing; raise the front

of the spring and fasten with a 9/16” X 3-1/4” hex bolt and 9/16”

hex lock nut. Repeat on the opposite side of the axle.

For installation of the front spring and axle repeat the previous

procedure, however, place the bushing in the rocker box in the

hook end of the spring. Insert the bolts and secure with 9/16” lock

nuts as before.

Mount the tire and rim assemblies using 80-90 ft. lbs. of torque on

the lug nuts using a proper tightening apparatus/tool.

Tongue:

Slip the tongue into the front frame cap of the frame. Line up the

holes, fasten the tongue in the frame with a 1/2” X 4” carriage bolt

and 1/2” flange lock nut at the front of the frame cap; fasten the

tongue in the rear with a 1/2” X 4-1/2” hex bolt and 1/2” flat washer

under the nut and bolt. String the tongue wire to the hole on the

side of the tongue and pull the tongue wire through the hole. Place

a rubber grommet in the wire hole over wires. Plug the tongue

harness into the frame harness.

Safety Chain:

Place a safety chain at the front of the tongue. Insert a 1/2” X 5”

hex bolt through the through a link on the chain and then through

hole provided in the tongue. Place the other safety chain over the

bolt threads and secure with a 1/2” flange lock nut. Tighten.

Winch Post:

Position the winch post assembly on the tongue. Secure with two

(2) 1/2” X 5” tongue u-bolts and 1/2” flange lock nuts. Tighten.

Fasten the winch handle to the winch.

Bunk Models:

Place assembled bunk on the rear support tube (Ref.#109).

Secure the bunks in the outside holes of the rear support tube with

1/2” 4-1/2” hex bolts and 1/2” flange lock nuts.

Roller Models:

This manual is related to the following products: