ShoreLand'r LEB29CBLW V.1 - Manual (Page 6)

Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorelandr.com
0003284
Page REV C 12/19/06
TONGUE
The tongue is shipped separate of the frame. Locate the appropri-
ate tongue and install by sliding it in the front of the tongue chan-
nel.
Line the holes in the tongue with the holes in the tongue channel.
Install the 1/2” x 4” hex bolt in the front cross hole and secure with
a 1/2” lock nut.
Remove the wire harness from the rear of the tongue. Place the
wire harness and the brake line through the hole provided in the
tongue cover plate.
Secure the tongue cover plate in position with the same 1/2” x 1-
1/2” hex bolt that secures the back on the tongue to the tongue
channel of the frame. Secure with a 1/2” lock nut. Tighten both bolts
just installed.
Plug the tongue wire harness ends into the frame harnesses by
matching colors and ends. Push the extra wire provided either into
the rear of the tongue or else remove the grommet in the side frame
and place the extra wire in the side frame. Replace grommet just
removed.
Locate the brass brake line coupling. Remove the plastic cap and
thread the brake line coming out the rear of the tongue into one
end of the coupling. Bend the line in a smooth gradual radius being
careful not to kink the line. Bend so it can be mated to the brake
line from the side frame. Once aligned, thread the side frame brake
line into the other end of the coupling. Tighten both lines into the
coupling.
SAFETY CHAINS
Locate the 1/2” x 5” hex bolt. Slip the bolt through a 1/2” flat washer,
then place through the last link of one of the safety chains.
Place the bolt with chain attached through the hole provided in the
bottom front of the actuator mount on the tongue. Place the second
chain on the portion of the bolt extending through the other side
of the tongue. Place on another 1/2” flat washer and hex lock nut.
Tighten.
SPARE TIRE MOUNTING BRACKET
The first step in mounting the spare tire bracket is to determine the cor-
rect orientation of the trailer. Standing at the rear of the trailer and look-
ing forward, your right hand is the right-hand side of the trailer.
Mount the spare tire bracket on the right-hand side frame of your
trailer at a location somewhere between the very front of the frame
and the first cross member. The exact positioning is dependant
upon the size and style of your boat.
Once identified, attach the spare tire bracket to the side frame us-
ing the U-bolts provided in the kit. Note that the spare tire bracket
is designed to fit both 2” x 4” and 2” x 5” side frames. Use the 1/2”
x 4-9/16” x 3-1/2” U-bolt when mounting to the 2” x 4” side frame
and the 1/2” x 5-9/16” x 3” U-bolts when mounting to the 2” x 5” side
frame.
Place the U-bolts over the side frame in the desired location. Match
the holes in the spare tire bracket with the U-bolts just placed over
the side frame. Slide the spare tire bracket over the U-bolts. Secure
using 1/2” lockwashers and hex nuts. Tighten when desired location
is achieved.
The spare tire bracket is designed to fit a 5 bolt on 4.5” bolt circle
pattern wheel. Note that there are only three stud bolts in the spare
tire bracket which are sufficient to carry the tire and wheel assem-
bly. Align the three studs with the holes in the wheel assembly and
secure the wheel assembly to the spare tire bracket with three- 1/2”
tapered lug nuts provided in the kit. Tighten securely to make sure
the wheel assembly does not come loose and fall off while trans-
porting the trailer.
Installation is complete.