HEIDENHAIN ND 1200R Quick Start - Manual (Page 3)

1
Controls and Displays
A LCD screen
B Soft keys: Change to support
functions
C Axis keys: Enter target
information
D Command keys: Control
operations
E Arrow cursor keys: Menu
navigation
F Fast track keys: Programmable
for frequently used functions
G Numeric keypad: Enter numeric
data
H Send key: Transmit data to PC,
USB printer or USB drive
I LCD on/off key: Turn LCD on or
off and clear data
Connections rear side
1 Power switch
2 Power connection with fuse
3 Ground (protective ground)
4 Encoder inputs, X, Y and Z axis.
5 RS-232-C interface for PC
connection. RS-232 cable must
not include crossovers.
6 Probe connector for
HEIDENHAIN 15 pin universal
touch probe sensor.
7 Unused
Connections side view
8 Audio out, for 3.5 mm
headphone / speaker jack,
monaural, 8 Ohm
9 USB type A interface for printer
or data storage
10 Remote accessory interface
RJ-45 for optional foot switch or
keypad accessory. Two optional
remote accessories can be used
simultaneously using an RJ-45
splitter.
Mounting
The ND 1200 R is secured to the swivel
slots of the mounting stand or arm
mount by a shoulder screw, a cap
screw mount as shown and associated
washers.
Initial power up
Press the power • switch to power
the ND 1200 R. The startup screen is
displayed. Press the FINISH key to
display the current axis positions on
the DRO screen.
Software setup
The operating parameters of the
ND 1200 R must be confi gured prior
to using it for the fi rst time, and any
time part measurement, reporting or
communication requirements change.
Settings will be retained until:
The data-backup battery is changed •
The data and settings are cleared •
Caution
Setup parameters control the operation
of the ND 1200 R and are password-
protected. Only qualifi ed personnel
should be given password access to
setup screens.
Access setup menu 1.
Press the MENU soft key and then the
SETUP soft key. The setup menu is
displayed.
Select the language 2.
Use the arrow cursor • keys to highlight
the desired language fi eld.
Press the
• YES soft key.
Press the • FINISH key.
Enter password 3.
Use the arrow cursor • keys to navigate
to the SUPERVISOR setup screen.
Highlight the
• PASSWORD fi eld and
enter the password.
Enable
• STARTUP ZERO if a machine
zero will be used for error correction.
Press the
• FINISH key.
ND 1200 R RADIAL
Setup
For detailed description, see www.heidenhain.de
Very important
Please note
For your information
English
Before Power up
Electrical connection
Line voltage: 100V~ to 240V
(–15 % to +10 %)
Line frequency: 43 Hz to 63 Hz
Line fuse: T1600 mA, 250 V
5 x 20 mm
Power connector wiring
L: Line voltage (brown)
N: Neutral (blue)
Earth ground (yellow/green)
Danger of electrical shock!
Do not open the enclosure •
Never use 3-wire to 2-wire adapters •
or allow the ground connection to
the ND 1200 R to be interrupted or
disconnected.
Caution
Changes to the power cable may be
made only by an electrical technician.
Caution
Do not connect encoders or other
equipment to the ND 1200 R when the
power is on.
Safety Considerations
General accepted safety precautions
must be followed when operating the
ND 1200 R. Failure to observe these
precautions could result in damage to
the equipment, or injury to personnel.
It is understood that safety rules within
individual companies vary. If a confl ict
exists between the material contained
in this guide and the rules of a company
using this system, the more stringent
rules should take precedence.