AML ACC-5910 M5900 In-Line Charger - Manual (Page 2)

To connect power to the charger:
1. Plug-in the Power Supply to a standard AC electrical outlet.
2. Connect the Power Supply Plug to the barrel power jack on
the adapter.
3. The adapter’s LED will turn green to indicate that power is
available.
4. The LED will remain green until a terminal is connected.
Charging
Turn the M5900 terminal off and insert the ACC-5910 Modular plug into the
bottom of the M5900. It begins to charge as soon as it is inserted. To properly
charge the battery, be sure the terminal is off.
Indicator Lights
Troubleshooting
Introduction
The ACC-5910 Terminal Charger charges the M5900 portable data terminal and has
a built-in null-modem adapter that allows RS232 serial communication.
About This Guide
This guide provides instruction on setting up and using the ACC-5910 M5900
Terminal Charger. For instructions on battery charging, see the M5900 User’s Guide.
Set Up
Setting up the ACC-5910 includes unpacking, connecting the power cable,
connecting a serial cable, and placing on a tabletop.
Unpacking the Terminal Charger
The shipping box includes the following:
· One ACC-5910 M5900 Terminal Charger
· One RJ Connector Cable
· One PWR-7100 Power Supply (120VAC) or
PWR-7150 (220VAC)
· One Line Cord with PWR-7150
· One DB-9 M-F Data Cable
· This User’s Guide
If any parts are missing or damaged, contact your authorized Customer
Support Representative immediately. Save the shipping box for storing or
shipping.
Connecting the Power
The PWR-7100 power supply is included with the ACC-5910 M5900 Terminal
Charger for 120VAC. The PWR-7150 power supply is included with the
ACC-5910 M5900 Terminal Charger for 220VAC along with a country specific
line cord.
Use only an American Microsystems, Ltd. approved power supply; output rated
5 VDC and a minimum of 2.4 Amps. The power supply connects to the
ACC-5910 by a 2.1mm x 5.5mm barrel connector, center positive.
© 2013 AML
2190 Regal Parkway • Euless, TX 76040
800.648.4452 • Local: 817.571.9015
© 2013 AML
2190 Regal Parkway • Euless, TX 76040
800.648.4452 • Local: 817.571.9015
© 2013 AML
2190 Regal Parkway • Euless, TX 76040
800.648.4452 • Local: 817.571.9015
LED Color Description
Off No power supplied to terminal charger.
Green If no terminal is connected to the charger,
green indicates that there is power available.
If a terminal is present, green indicates that
the terminal is fully charged.
Red Terminal or battery is connected to the
charger and the battery is being charged.
Symptom
LED does not light
when the charger is
powered on.
LED stays green when
the terminal is
connected.
LED stays red for more
than 6 hours.
Cause
Terminal charger is not
receiving power.
Connector and
terminal are not
connected firmly, or
the battery is not
properly installed in
the terminal.
Battery is charged.
Battery faulty and can
not be charged.
Suggested Action
Make sure the power
supply is securely
connected and
receiving power.
Make sure the battery
is properly installed in
the terminal, and
reseat the connector
onto the terminal.
Normal status.
Replace battery with
an AML approved
battery.
The M5900 Communications Ports
10 9 8 7 6 5 4 3 2 1
4 3
1 2
The M5900 Terminal Charger
A fully discharged
battery takes about 4
hours to completely
recharge.
When the battery charging LED
is red, the battery is charging.
When the battery charging LED
is green the battery is fully charged