AML ACC-5935 4-Position Handheld Charger User Manual
User’s guide, Acc-5935, Position terminal charger

User’s Guide
ACC-5935
4-Position
Terminal Charger
© 2013 AML
2190 Regal Parkway • Euless, TX 76040
800.648.4452 • Local: 817.571.9015
www.amltd.com • 800.648.4452
© 2013 AML
© 2013 AML
2190 Regal Parkway • Euless, TX 76040
800.648.4452 • Local: 817.571.9015
Safety
NOM / NYCE-NOM-019-SCFI-1998
Safety of data processing equipment.
Normalización y Certificación Electronica (NYCE)
Regulatory Information
All American Microsystems, Ltd. devices are designed to be compliant
with rules and regulations in locations they are sold and will be labeled
as required. Any changes or modifications to American Microsystems,
Ltd. equipment, not expressly approved by American Microsystems,
Ltd., could void the user's authority to operate the equipment.
Power Supply
Use only an American Microsystems, Ltd. approved Power Supply,
output rated 12 VDC and minimum 5A. The Power Supply is certified
to EN60950.
Disclaimer
American Microsystems, Ltd. reserves the right to make changes in
specifications and other information contained in this document without
prior notice, and the reader should in all cases consult American Microsys-
tems, Ltd. to determine whether any such changes have been made. The
information in this publication does not represent a commitment on the
part of American Microsystems, Ltd.
American Microsystems, Ltd. shall not be liable for technical or editorial
errors or omissions contained herein; nor for incidental or consequential
damages resulting from the furnishing, performance, or use of this material.
This document contains proprietary information that is protected by
copyright. All rights are reserved. No part of this document may be
photocopied, reproduced, or translated into another language without
the prior written consent of American Microsystems, Ltd.
FCC Declaration of Conformity
Product Name: 4-Position Terminal Charger
Model Number: ACC-5935
Radio Frequency Interference Requirements
This equipment complies with Part 15 of the FCC rules. Operation is subject
to the following two conditions: (1) This equipment may not cause harmful
interference, and (2) this equipment must accept any interference
received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for
a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interfer-
ence when the equipment is operated in a residential environment. This
equipment generates uses and can radiate radio frequency energy,
and if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation.
If you determine the equipment does cause harmful interference to
radio or television reception (this may be determined by monitoring the
interference while turning the equipment off and on), you are encour-
aged to try to correct the interference by one of the following measures:
· Reorient or relocate the receiving antenna.
· Increase the separation between the equipment and receiver.
· Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
· Consult the dealer or an experienced radio or TV technician for help.
Radio Frequency Interference Requirements - Canada
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme
NMB-003 du Canada.
Marking and European Economic Area (EEA)
Products intended for sale within the European Union are
marked with the CE mark which indicates compliance to
applicable Directives and European Normes (EN), as follows.
Amendments to these Directives or EN’s are included.
· Electromagnetic Compatibility Directive 89/336/EEC
· Low Voltage Directive 73/23/EEC
The ACC-5935 4-Position Terminal Charger
charges AML handhelds including models
M7225, M7220/7221, M71V2 and M5900.