AML ACC-5925 Charging Cradle - Manual (Page 2)

To connect power to the cradle:
1. Plug-in the Power Supply to a standard AC electrical outlet.
2. Connect the Power Supply Plug to the barrel power jack on the cradle.
3. The cradle LED’s will turn green to indicate that power is available.
4. The LED’s remain green until a terminal or battery is inserted into the slots.
Charging
For wireless handhelds, turn the terminal off and insert it into a cradle slot for
an optimum charge. It begins to charge as soon as it is inserted.
Batch collection devices, including the M5900 series terminals, should be
charged while powered on. These units will automatically power on if inserted
into the ACC-5925 when in off or suspended modes.
Indicator Lights
Troubleshooting
The Terminal Charger
The cradle automatically charges the terminal battery while it is resting in the
cradle. The cradle also includes an extra slot to charge a spare battery. The
Terminal Charger can accommodate the terminal with or without the optional
pistol grip handle.
The Terminal Charger has three indicator lights:
- Indicates that the terminal charger is plugged in.
- Indicates the terminal main battery is charging.
- Indicates the spare battery is charging.
When the battery charging LED is red, the battery is charging. When the battery
charge LED is green, the battery is fully charged. A fully discharged battery
takes about 6 hours to completely recharge.
Introduction
The ACC-5925 Terminal Charger charges any AML M7225, M7220, M71V2, or
M5900 Series handheld terminal, along with one spare battery.
About This Guide
This guide provides instruction on setting up and using the ACC-5925 Terminal
Charger.
Set Up
Setting up the cradle includes unpacking, connecting the power cable, and
mounting the cradle on a table top.
Unpacking the Cradle
The shipping box includes the following:
· One ACC-5925 Terminal Charger
· One PWR-7100 Power Supply (120VAC)
or PWR-7150 (220VAC)
· One Line Cord with PWR-7150
· This User’s Guide.
If any parts are missing or damaged, contact your authorized Customer
Support Representative immediately. Save the shipping box for storing or
shipping.
Connecting the Power
The PWR-7100 power supply is included with the ACC-5925 Terminal Charger
for 120VAC. The PWR-7150 power supply is included with the ACC-5925
Terminal Charger for 220VAC, along with a country specific line cord.
Use only an American Microsystems, Ltd. approved power supply rated at 5
VDC at a minimum of 2.8 Amps. The power supply connects to the ACC-5925
by a 2.1mm x 5.5mm, barrel center-positive connector.
© 2013 AML
2190 Regal Parkway • Euless, TX 76040
800.648.4452 • Local: 817.571.9015
© 2013 AML
2190 Regal Parkway • Euless, TX 76040
800.648.4452 • Local: 817.571.9015
© 2013 AML
2190 Regal Parkway • Euless, TX 76040
800.648.4452 • Local: 817.571.9015
LED Color Description
Off No power supplied to terminal charger.
Green If no terminal is present in the charger, green indicates that
there is power available. If terminal is present, green
indicates that the terminal is fully charged.
Red Terminal or battery is present in the terminal charger and the
battery is being charged.
Symptom
LED does not light when
the terminal charger is
powered on.
LED stays green when the
terminal is inserted.
LED stays red for more
than 6 hours.
Cause
Terminal charger is not
receiving power.
Terminal is not seated
firmly in the terminal
charger, or the battery is
not properly installed in
the terminal.
Battery is charged.
Battery faulty and can not
be charged.
Suggested Action
Make sure the power
supply is securely
connected and receiving
power.
Make sure the battery is
properly installed in the
terminal, and reseat the
terminal in the terminal
charger.
Normal status.
Replace battery with an
AML approved battery.
Spare Battery