Operation – Tri Tool 602-5SBM Clamshell Air User Manual
Page 20
20
TRI TOOL INC.
92-0093 Rev. 131230
OPERATION
Locking Screw Locations
Read the operation instructions carefully before attempting to operate the Model
602.5SBM Low Profile Clamshell.
See ‘Configure the Clamshell for the specific task required’ later in this section to
configure the machine.
Do not install the Tool Bits until the Clamshell is installed on the pipe.
INSTALLATION OF THE CLAMSHELL ON AN IN-LINE PIPE
Separate the two halves of the Clamshell.
Disengage the Air Motor by removing the Motor Hold-down Bolt and removing the
Air Motor from the drive socket.
LOCKING
SCREWS
HOUSING
LOCKING
SCREWS
HEADSTOCK
By hand, rotate the Headstock until the split-lines of the Headstock match the
split-line of the Housing.
Unbolt the two halves of the Clamshell.
Two Locking Screws are located on the Housing and two more on the Headstock.
These Locking Screws are captured in their holes so that they will not come totally
free of the Clamshell. Refer to “Locking Screw locations”.
- 204B Cutting Head (9 pages)
- 204B Cutting Head (10 pages)
- 204B Cutting Head (9 pages)
- 212B Single Point Spring Hanger Assembly (8 pages)
- 204B Cutting Head (13 pages)
- 204B Cutting Head (36 pages)
- 204B Cutting Head (17 pages)
- 201BA Beveler (36 pages)
- 204B Elbow Mandrel (16 pages)
- 204B Beveler (45 pages)
- 204B Flange Facer (21 pages)
- 206B Elbow Mandrel (17 pages)
- 206B Flange Facer (22 pages)
- 206B Beveler (45 pages)
- 212B ID Tracking Module (17 pages)
- 206B Miter Mandrel (16 pages)
- 206B Sleeve Mandrel (13 pages)
- 208B Elbow Mandrel (20 pages)
- 208B ID Tracking Module (18 pages)
- 208B Miter Mandrel (20 pages)
- 208B Flange Facer (28 pages)
- 208B Sleeve Mandrel (15 pages)
- 212B Elbow Mandrel (16 pages)
- 214B Beveler Single Point Flange Facer (41 pages)
- 212B Flange Facer (22 pages)
- 212B Miter Mandrel (20 pages)
- 212B Single Point Hydraulic Motor Assembly (9 pages)
- 212B Single Point Flange Facer Miter Mandrel (28 pages)
- 212B Sleeve Mandrel (12 pages)
- 214B Elbow Mandrel (20 pages)
- 214B Flange Facer (23 pages)
- 214B ID Track Module (19 pages)
- 214B Miter Mandrel Head Kit (22 pages)
- 214B Sleeve Mandrel (13 pages)
- 236B ID Tracking Module (23 pages)
- 224B Miter Mandrel (27 pages)
- 224B Single Point (30 pages)
- 230B Beveler Flange Facer (16 pages)
- 230B ID Tracking Module (15 pages)
- 230B Lifting Frame (19 pages)
- 236B Miter Mandrel (25 pages)
- 301SP Tube Squaring (35 pages)
- 236B Single Point (32 pages)
- 302 Tube Squaring Micro Feed Assembly (11 pages)
- 302 Tube Squaring (31 pages)