Spohn 782-F - Manual

Spohn Performance
,
Inc.
494 E Lincoln Ave - Myerstown, PA 17067
1-888-365-6064 www.spohn.net
Part# 782-F | Tubular Front Lower A-Arms
1982-1992 GM F-Body Camaro & Firebird
USE OF THIS PRODUCT IS ACCEPTANCE OF SELLER’S DISCLAIMER OF WARRANTY!
By their very nature, competition components are constantly pushed to their limits. While our components
are designed to withstand intense race conditions, it is impossible to control the quality of installation or
the varying conditions in which they are used. It is for this reason that absolutely no warranty or
guarantee is either written or implied. Neither the seller or the manufacturer will be liable for any loss,
damage, or injury – direct or indirect – arising from the use of or inability to determine the use of any
product. Before using, the user should determine the suitability of the product for its intended use, and
the user shall assume all responsibility in connection therewith. Spohn Performance, Inc. makes no
guarantee as to the legality for any specific class. Spohn Performance, Inc. makes no claims, nor does it
intend its products to be used in street driven vehicles. Spohn Performance, Inc. reserves the right to
make changes in design or add to or improve on their product without incurring any obligation to install
the same on product previously manufactured. The Buyer agrees to indemnify and hold Spohn
Performance, Inc. harmless from any claim, action or demand arising out of or incident to the Buyer’s
installation or use of products purchased from Spohn Performance, Inc.
INSTALLATION INSTRUCTIONS
1. This installation should only be performed by an experienced mechanic. Improper coil
spring removal and installation can result in serious injury. If you are not experienced
in this type of installation we recommend you have the installation performed by a
professional mechanic at a commercial garage and/or alignment shop.
2. Begin by jacking up the front of the vehicle and then place jack stands under the
frame to safely support the vehicle. The front wheels need to be off of the ground.
3. Remove both front wheels.
4. On The Driver's Side Only: Remove the front sway bar end link from the a-arm and
the sway bar and discard.
5. Turn the spindle all the way in one direction for easier access to the lower ball joint.
Remove the cotter pin from the castle nut on the lower ball joint. Then loosen the
castle nut, but do NOT completely remove it. Using a hammer, hit the spindle around
the ball joint mounting hole until the ball joint pops loose. You may need to use a
pickle fork.
6. Position a jack under the a-arm in the area of the ball joint. Jack up on the a-arm until
there is no tension on the ball joint.
7. Insert an internal spring compressor through the bottom of the a-arm and up through
the inside of the coil spring. Fully compress the spring using the internal spring
compressor (we recommend using our Part# FCSC1 internal coil spring compressor
that is designed specifically for this F-Body application. It makes the job VERY easy!).
8. Remove the castle nut from the lower ball joint.
9. Support and hold the spindle, brakes, etc. up in the car. You must tie this assembly up
using wire or rope.
10. Carefully lower the jack you placed underneath the lower a-arm and lower the a-arm
as far as it will come down. Hold onto the spring and remove it when it is free as you
lower the a-arm.
11. While holding onto the a-arm, remove both of the mounting bolts that go through the
a-arm bushings at the frame mounts and then remove the a-arm from the vehicle.
12. Lightly sand and/or wire wheel the insides of the k-member mounts where the a-arm
bushings ride. When you have removed all dirt, rust and scale from these mounting
areas apply a liberal amount of grease to these areas of the mounts. See the end of
these instructions for information on what type of grease must be used.
13. Properly identify the left side Spohn Performance front lower a-arm. The sway bar end
link and polyurethane bump stop face the FRONT of the vehicle when installed.
14. Apply a liberal amount of grease to the outside faces of all four bushing ends. See the
end of these instructions for information on what type of grease must be used.
15. Mount the a-arm into the k-member mounts and loosely install both mounting bolts.
Do NOT completely tighten them, just lightly snug the nuts.
1