SOMFY DECOFLEX WIREFREE RTS - Manual (Page 2)

Ref. No. 25018190 SOMFY SYSTEMS, INC. 9/13 C
SOMFY SYSTEMS, INC. reserves the right to change,
update or improve this document without prior notice.
5. Insert bracket (as shown) into
hole, keeping the thin side
closest to the edge of the existing
switch box. 6. Carefully bend bracket tabs 90
degrees behind the dry-wall to
ensure a tight secure fit.
7. Position the DecoFlex RTS
switch into mounting bracket
aligning the screw holes. Ensure
that the wire antenna remains as
straight as possible behind the
wall. Secure switch to mounting
bracket with screws (provided). 8. Attach a new (2 gang) or
double gang Decora style wall
plate over both switches to
complete installation.
REPLACING THE BATTERY
5
TM The DecoFlex WireFree RTS switch is designed to provide years of maintenance free performance. Should the battery become
discharged, the LED indicator lights will no longer function when the channel button is selected or an Up/Stop/Down command
is activated. As a result, the radio signal will be reduced or not communicated to the RTS receiver or motor.
TM The battery can be easily replaced by exposing the SWITCH BASE ASSEMBLY board of the DecoFlex WireFree switch. Simply
slide the battery out of its holder and replace with a new 3V Lithium battery (type 2450) maintaining the correct polarity.
NOTE:
Batteries should be disposed of properly according to local regulations.
* Hole dimensions for (Step 4) mounting bracket (1 5/8 ” W x 3 7/16 ” L)
FCC INFORMATION
WARNING: Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Results. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including that which may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for CLASS B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and , if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna 2. Increase the separation between the equipment and receiver
3. Connect the equipment into an outlet on a circuit different from that to which receiver is connected 4. Consult the dealer or experienced radio/TV technician for help.
6
ASSEMBLE 2, 3, & 4 CHANNEL SWITCHES
1. Begin with a standard (assembled) 1 or 5 channel button DecoFlex switch - Using a
small flat blade screw driver, carefully separate the SWITCH BASE ASSEMBLY from
the FACEPLATE (as shown in figure 1).
2. Add or remove CHANNEL BUTTONS (as required) from the SWITCH BASE ASSEMBLY
(as shown in figure 2). Be certain the SWITCH BASE ASSEMBLY remains intact.
3. Attach new 2, 3, or 4 channel button face plate (as shown in figure 3 & 4).
7
REPLACE STANDARD (BLANK) CHANNEL BUTTONS
WITH PRINTED CHANNEL BUTTONS
1. Using a small flat blade screw driver, carefully separate the SWITCH BASE ASSEMBLY from the
FACEPLATE (as shown in figure 1).
2. Replace standard (blank) or temporary labeled CHANNEL BUTTON(s) with new printed CHANNEL BUTTON(s).
3. Attach new CHANNEL BUTTON FACE PLATE (as shown in figure 3 & 4).
INSTALLATION CONT’D
4
Figure 1.
Figure 2.
Figure 3.
Figure 4.
Removable
Channel Buttons
Switch Base
Assembly
5 Channel
Faceplate Wall Plate
5 Channel DecoFlex
Wall Switch
(Exploded view)
2 Channel
Switch Assembly
3 Channel
Switch Assembly
4 Channel
Switch Assembly
121 Herrod Boulevard
Dayton, NJ 08810
Phone: US: 1-800-22-SOMFY
NJ: (609) 395-1300
Fax: General (609) 495-8117
SOMFY SYSTEMS, INC.
North America Headquarters
5178 Everest Drive
Mississauga, Ontario L4W2R4
Phone: CN: (800)-667-6639
Phone: (905) 564-6446
Fax: (905) 238-1491
SOMFY ULC
SOMFY Canada Division