Smithco Big Vac V72E (sn 73001 – 73020) Parts & Service Manual - Manual (Page 47)

45
Accessories
73-005 5TH WHEEL FOR TRACTOR
REF# PART# DESCRIPTION QUANTITY
1 73-045 Hose Guard Cover 1
2 HSDPS-14-100 Pan Head Drill Screw 1 /
4
x 1 2
HW-14 Washer 1 /
4
2
3 HB-516-18-075 Bolt 5 /
16
- 18 x 3 /
4
4
HNFL-516-18 Flange Whiz Lock Nut 5 /
16
- 18 4
4 73-044 Hose Guard 1
5 73-038 5th Wheel Gooseneck 1
6 HB-12-13-125 Bolt 1 /
2
-13 x 1 1 /
4
8
HNTL-12-13 Lock Nut 1 /
2
- 13 8
7 25-358 Decal, Smithco 1
8 78-390 Ball Lock Arm 1
. 9 HB-516-18-100 Bolt 5 /
16
- 18 x 1 1
HNTL-516-18 Lock Nut 5 /
16
-18 1
10 42-539 Lynch Pin 2
11 18-371 2"Ball 1
12 7-029 Hitch Pin 3 /
4
x 4 1
13 73-039 3-Point Hitch 1
14 HB-14-20-075 Bolt 1 /
4
- 20 x 3 /
4
1
HNTL-14-20 Lock Nut 1 /
4
- 20 1
15 HB-38-16-225 Bolt 3 /
8
- 16 x 2 1 /
4
1
HW-38 Washer 3 /
8
2
HNTL-38-16 Lock Nut 3 /
8
- 16 1
16 HB-38-16-225 Bolt 3 /
8
- 16 x 2 1 /
4
1
HW-38 Washer 3 /
8
1
HNW-38-16 Wing Nut 3 /
8
- 16 1
17 78-352 Control Panel Mount 1
18 HST-14-20-075 Truss Head Bolts 1 /
4
- 20 x 3 /
4
4
HNFL-14-20 Flange Lock Nuts 1 /
4
- 20 4
INSTALLATION INSTRUCTIONS
Use two people to install hitches.
1. Block both wheels so machine does not roll.
2. Remove tires (Ref 6) from wheels on sweeper and mount on new wheels (Ref 7) suppplied with kit. Block rear of
machine up. Remove the rear tires and rear hubs. All parts except hubs to be reused.
3. Put new wheel assembly back on and hold in place with the 1 /
2
-20 lug nuts.
4. Check all nuts and be sure they are tight.
5. Use the jack that is part of the sweeper to raise or lower sweeper to comfortable working height.
6 Slide the gooseneck (Ref 2) under the sweeper frame. Use the eight 1 /
2
- 13 x 1 1 /
4
bolts (Ref 3) and lock nuts oto
secure goseneck. Tighten all hardware.
7. Install the control panel mount (Ref 1) on the front of the gooseneck (Ref 2) as shown, using two 3 /
8
- 16 x 2 1 /
4
bolts (Ref 15 and 16). On the bottom bolt use lock nut (Ref 15) and just tighten snug. On the top bolt use the 3 /
8
washer and wing nut (Ref 16). Tighten both after adjusting for the proper position.
8. The control panel has all hose, wiring and throttle cable connected to it and the sweeper. The control panel is
wrapped and fastened to the front of the sweeper.
9. Remove the control panel from the sweeper, bring it forward with the hoses to the rear and the throttle on the left
hand side.
10. Fasten the control panel to the control panel mount with the four Truss Head Bolts 1 /
4
- 20 x 3 /
4
(Ref 17) and four
Flange Lock Nuts. Tighten all hardware.
11. Intall 3-point Hitch (Ref 13) on tractor. Install 2" Ball (Ref 12) into 3-point hitch.