Smithco Big Vac V72E (sn 73001 – 73020) Parts & Service Manual - Manual (Page 45)

43
Accessories
73-004 5THE WHEEL HITCH FOR TURF TRUCKSTER W/ ELECTRIC BRAKES
REF# PART# DESCRIPTION QUANTITY
1 73-045 Hose Guard Cover 1
2 HSDPS-14-100 Pan Head Drill Screw 1 /
4
x 1 2
HW-14 Washer 1 /
4
2
3 HB-516-18-075 Bolt 5 /
16
- 18 x 3 /
4
4
HNFL-516-18 Flange Whiz Lock Nut 5 /
16
- 18 4
4 73-044 Hose Guard 1
5 73-038 5th Wheel Gooseneck 1
6 HB-12-13-125 Bolt 1 /
2
-13 x 1 1 /
4
8
HNTL-12-13 Lock Nut 1 /
2
- 13 8
7 73-041 LH Backplate 1
73-042 RH Backplate 1
8 72-162 Hub & Drum Assembly 2
9 33-072-01 Tire 1
10 78-103-02 Wheel 2
11 HN-716-20 Nut 7 /
16
- 20 8
HWL-716 Lock Washers 7 /
16
8
12 25-358 Decal, Smithco 1
. 13 HB-516-18-100 Bolt 5 /
16
- 18 x 1 1
HNTL-516-18 Lock Nut 5 /
16
-18 1
14 78-390 Ball Lock Arm 1
15 HB-14-20-075 Bolt 1 /
4
- 20 x 3 /
4
1
HNTL-14-20 Lock Nut 1 /
4
- 20 1
16 HB-38-16-225 Bolt 3 /
8
- 16 x 2 1 /
4
1
HW-38 Washer 3 /
8
1
HNTL-38-16 Lock Nut 3 /
8
- 16 1
17 HB-38-16-225 Bolt 3 /
8
- 16 x 2 1 /
4
1
HW-38 Washer 3 /
8
1
HNW-38-16 Wing Nut 3 /
8
- 16 1
18 78-352 Control Panel Mount 1
19 HST-14-20-075 Truss Head Bolts 1 /
4
- 20 x 3 /
4
4
HNFL-14-20 Flange Lock Nuts 1 /
4
- 20 4
INSTALLATION INSTRUCTIONS
Use two people to install hitches.
1. Block both wheels so machine does not roll.
2. Use the jack that is part of the sweeper to raise or lower sweeper to comfortable working height.
3. Slide the gooseneck (Ref 5) under the sweeper frame. Use the eight 1 /
2
- 13 x 1 1 /
4
bolts (Ref 6) and lock nuts oto
secure goseneck. Tighten all hardware.
4. Install the control panel mount (Ref 19) on the front of the gooseneck (Ref 5) as shown, using two 3 /
8
- 16 x 2 1 /
4
bolts (Ref 17 and 18). On the bottom bolt use lock nut (Ref 18) and just tighten snug. On the top bolt use the 3 /
8
washer and wing nut (Ref 17). Tighten both after adjusting for the proper position.
5. The control panel has all hose, wiring and throttle cable connected to it and the sweeper. The control panel is
wrapped and fastened to the front of the sweeper.
6. Remove the control panel from the sweeper, bring it forward with the hoses to the rear and the throttle on the left
hand side.
7. Fasten the control panel to the control panel mount with the four Truss Head Bolts 1 /
4
- 20 x 3 /
4
(Ref 19) and four
Flange Lock Nuts. Tighten all hardware.
9. Lay the hoses, wiring and throttle cable on top of the gooseneck in hose guard(Ref 4). secure hose guard cover
(Ref 1) with Bolt
5 /
16
- 18 x 3 /
4
(Ref 3) and Flange Lock Nuts.
Do not tow on public roads.