Smithco Big Vac V72E (sn 73001 – 73020) Parts & Service Manual - Manual (Page 43)

41
Accessories
73-003 STANDARD CLEVIS HITCH PARTS LIST
REF# PART# DESCRIPTION QUANTITY
1 72-119 Control Panel Adjustment 2
2 HB-38-16-250 Bolt 3 /
8
- 16 x 2 1 /
2
3
HNTL-38-16 Lock Nut 3 /
8
- 16 3
3 HB-38-16-275 Bolt 3 /
8
- 16 x 2 3 /
4
1
HW-38 Washer 3 /
8
2
HNTL-38-16 Lock Nut 3 /
8
- 16 1
4 73-040 Control Panel Mount 1
5 HB-38-16-250 Bolt 3 /
8
- 16 x 2 1 /
2
2
HW-38 Washer 3 /
8
4
HNTL-38-16 Lock Nut 3 /
8
- 16 2
6 78-240 Jack (part of machine) 1
7 HB-12-13-125 Bolt 1 /
2
-13 x 1 1 /
4
8
HNTL-12-13 Lock Nut 1 /
2
- 13 8
8 72-086 Tongue 1
9 78-244 Adjustable 3 /
4
" Clevis Hitch 1
10 78-245 2-5/16 Ball Hitch (Optional)
11 HB-12-13-250 Bolt 1 /
2
-13 x 2 1 /
2
(comes with 78-244 abd 78-245) 8
HNTL-12-13 Lock Nut 1 /
2
- 13 (comes with 78-244 abd 78-245) 8
12 HB-38-16-250 Bolt 3 /
8
- 16 x 2 1 /
2
1
HW-38 Washer 3 /
8
2
HNTL-38-16 Lock Nut 3 /
8
- 16 1
13 60-323 Spring 1
14 HB-516-18-100 Bolt 5 /
16
- 18 x 1 1
HW-516 Washer 5 /
16
2
HNTL-516-18 Lock Nut 5 /
16
- 18 1
15 15-020 Hand Grip 1
16 72-093 Adjustment Lock Arm 1
17 72-121 Control Panel Leg 1
18 72-120 Adjustment Leg 1
19 HST-14-20-075 Truss Head Bolts 1 /
4
- 20 x 3 /
4
4
HNFL-14-20 Flange Lock Nuts 1 /
4
- 20 4
INSTALLATION INSTRUCTIONS
Use two people to install hitches.
1. Block both wheels so machine does not roll.
2. Use the jack that is part of the sweeper to raise or lower sweeper to comfortable working height.
3. Slide the tongue (Ref ) under the sweeper frame. Use the eight 1 /
2
- 13 x 1 1 /
4
bolts (Ref 7) and lock nuts to secure
tongue. Tighten all hardware.
4. Block up machine and remove jack form machine and place it on the tongue. Use the jack here for more
support.
5. Install the control panel leg(Ref 17) oand the adjustment leg (Ref 18) as shown, using two 3 /
8
- 16 x 2 1 /
2
bolts (Ref
5 and 12). INstall the control panel adjustment plates (Ref 1) using hardware (Ref 2 and 3)a as shown. Install
control panel arm (Ref 4).
6. Install the adjustment lock arm (Ref 16) with the bolt and the spring (Ref 13 an d14)as show. Put the hand griop
(Ref 15) on the arm. TIghten all hardware.
5. The control panel has all hose, wiring and throttle cable connected to it and the sweeper. The control panel is
wrapped and fastened to the front of the sweeper.
6. Remove the control panel from the sweeper, bring it forward with the hoses to the rear and the throttle on the left
hand side.
7. Fasten the control panel to the control panel mount with the four Truss Head Bolts 1 /
4
- 20 x 3 /
4
(Ref 19) and four
Flange Lock Nuts. Tighten all hardware.
Do not tow on public roads.