Smithco Super Rake 13-55х (sn 6201 – 6279/1080 – 1120) Parts & Service Manual - Manual (Page 63)

61
Accessories
13-395 FRONT MOUNT FAN RAKE PARTS LIST
REF# PART# DESCRIPTION QUANTITY
1 13-403 Handle 1
2 13-477 Left Extension 1
3 13-396 Fan Rake Holder 1
4 HB-14-20-175 Bolt 1 /
4
- 20- 1 3 /
4
2
HNCL-14-20 Center Lock Nut 1 /
4
- 20 2
5 HB-38-16-225 Bolt 3 /
8
- 16 x 2 1 /
4
4
HNCL-38-16 Center Lock Nut 3 /
8
-16 4
6 HB-516-18-175 Bolt 5 /
16
- 18 x 1 3 /
4
2
HWL-516 Lockwasher 5 /
16
2
HN-516-18 Nut 5 /
16
- 18 2
7 13-478 Right Extension 1
8 13-402 Edge Rake Holder 1
9 11-055 Compression Spring 1
10 HNTL-38-16 Lock Nut 3 /
8
- 16 1
11 HB-38-16-375 Bolt 3 /
8
- 16 x 3 3 /
4
1
12 HB-14-20-200 Bolt 1 /
4
- 20 x 2 6
HNCL-14-20 Center Lock Nut 1 / 4 - 20 6
13 13-310 Rake 6
14 13-472 Right Pusher Bar 1
15 HB-38-16-250 Bolt 3 / 8 - 16 x 2 1 / 2 (part of Trap Rake) 2
HW-38 Washer 3 / 8 (part of Trap Rake) 2
HNTL-38-16 Lock Nut 3 / 8 -16 2
16 21-445 Spring 2
17 13-474 Cross Brace 1
18 13-238 Release Lever 1
19 15-015 Pedal Pad 1
20 HCP-12-150 Clevis Pin 1 /
2
x 1 1 /
2
2
HHP-18 Bridge Pin 1 /
8
2
21 11-050 Spring 1
22 13-172 Plow Lift Holder 1
20-019 Bushing 2
HG-14-28-180 Grease Fitting 1 /
4
- 28 x 180° 1
23 13-473 Left Pusher Bar 1
24 15-013 Rubber Bumper 2
RAKE INSTALLATION
This Fan Rake Kit fits on the front bumper of the Super Rake. Any Current pusher bars must be removed from the machine. If the Sand
Plow is being replaced, the pedal release lever and plow lift holder can remain on the bumper. Simply disconnect the lower end of the (Ref#
16)Springs from the plow cross bar and leave the holder on the bumper. If the Super Rake has no attachments on the front end, bolt (Ref#
22)Plow Lift holder to the bumper using the same fasteners that hold the bumper to the underside of the console(nose cone).
1. Install (Ref# 23 & 14)Right and Left Pusher Bars to frame tabs using (Ref# 20)Clevis Pins and Bridge Pins.
2. Put (Ref# 17)Cross Bar in place and loosely hold it together with (Ref# 5)Bolts and Nuts.
3. Attach (Ref# 16)Springs to the holes in the Cross Brace.
4. If the fan rake bars are not pre-assembled, place the center (Ref# 3)Fan Rake Holder over the ends of Pusher Bars. Tighten the
cross brace and the fan rake holder to the pusher bars with (Ref# 5)Bolts and Nuts.
5. Insert (Ref# 2 & 7)Extensions in the ends of the center holder. Secure them with (Ref# 6)Fasteners.
(The straight (Ref# 2)Extension goes in the left end, the bent (Ref# 7)Extension goes in the right end).
6. Fasten (Ref# 8)Edge Rake Holder to the extension with (Ref# 11)Bolt, (Ref# 9) Spring and (Ref# 10)Lock Nut.
7. Fit the six (Ref# 13)Rakes over the holder tubes and secure them with (Ref# 12)Bolts and Nuts.
8. Insert (Ref# 1)Handle into the tube sockets of the center holder, lining up the desired holes and tightening with (Ref# 4)Bolts and
Nuts.
Test the installation by lifting the rake unit until it engages the hook of (Ref# 18)Pedal Release Lever. Press down on the Pedal release lever.
Pressing down on the pedal lever should allow the Rakes to drop and be guided by (Ref# 1)Handle for depth of raking. Lifting on the handle
should raise the rakes to engage the hook again until the rakes are needed again.