Dimplex DS7420 - Manual (Page 8)

8 www.dimplex.com
TO REPLACE UPPER LIgHT BULB
WARNINg: If unit was operating prior to servicing
allow at least 10 minutes for light bulbs and heating ele-
ment to cool off to avoid accidental burning of skin.
WARNINg: Disconnect power before attempting any
maintenance or cleaning to reduce the risk of electric
shock or damage to persons.
Light bulbs need to be replaced when you notice a dark
section of the flame or when the clarity and detail of the
log exterior disappears. There is one bulb at the top of the
opening that illuminates the log set exterior and two bulbs
under the log set which generate the flames and embers.
It is a good idea to replace all of the light bulbs at one
time if they are close to the end of their rated life. Group
replacement will reduce the number of times you need to
open the unit to replace the light bulbs.
Open door by pulling the handle. 1.
Locate the upper bulb bracket. 2.
Bend light retainer bracket down. 3.
Locate and remove the light bulb. 4.
Insert new bulb. 5.
Bend light retainer bracket back into its original posi- 6.
tion.
Close the door.
7.
UPPER LIgHT BULB REQUIREMENTS: Quantity of 1
clear chandelier or candelabra bulbs with an E-12 (small)
socket base, 7 watt rating.
TO REPLACE LOWER LIgHT BULBS
WARNINg:If unit was operating prior to servicing allow
at least 10 minutes for light bulbs and heating element to
cool off to avoid accidental burning of skin.
WARNINg:Disconnect power before attempting any
maintenance or cleaning to reduce the risk of electric
shock or damage to persons.
Light bulbs need to be replaced when you notice a dark
section of the flame or when the clarity and detail of the
log exterior disappears. There is one bulb at the top of the
opening that illuminates the log set exterior and three bulbs
under the log set which generate the flames and embers.
It is a good idea to replace all of the light bulbs at one
time if they are close to the end of their rated life. Group
replacement will reduce the number of times you need to
open the unit to replace the light bulbs.
Remove the stove pipe kit (if equipped). 1.
Gently place stove on its back on a flat surface. 2.
Remove the heater cover retaining screws located on 3.
the bottom of the stove and lower heater and light as-
sembly out onto the floor.
Remove the burnt out bulb(s) by pulling straight out
4.
of socket. If bulbs are difficult to remove form socket
move the bulb from side to side while pulling being
careful not to damage the light socket.
Replace the lower light bulbs.
5.
Reassemble in the reverse order as above. 6.
LOWER LIgHT BULB REQUIREMENTS: Quantity of 3
– 35 watt Halogen Quartz lamps, 120 volt, G9 base. DO
NOT ExCEED 35 WATTS PER BULB
TO REPLACE MAIN POWER SWITCH
WARNINg: If unit was operating prior to servicing
allow at least 10 minutes for light bulbs and heating ele-
ment to cool off to avoid accidental burning of skin.
WARNINg: Disconnect power before attempting any
maintenance or cleaning to reduce the risk of electric
shock or damage to persons.
Remove back panel screws located along the rear of 1.
the top panel.
Open front door and release the Cams located in the
2.
upper corner of both side panels.
! NOTE: To release Cams ensure arrow on Cam is facing
up.
arrow
Remove top panel. 3.
Locate the main on/off switch mounted on the rear 4.
panel and disconnect the wiring clips and connections
noting their original locations.
Depress the retainer clips on the rear of the switch and
5.
push the switch out of the rear cover.
Properly orient the new switch and connect all of the
6.
wiring clips and connections.
Reassemble in the reverse order as above.
7.
TO REPLACE UPPER LIgHT ON/OFF
SWITCH
WARNINg: If unit was operating prior to servicing
allow at least 10 minutes for light bulbs and heating ele-
ment to cool off to avoid accidental burning of skin.
WARNINg: Disconnect power before attempting any
maintenance or cleaning to reduce the risk of electric
shock or damage to persons.
Remove back panel screws located along the rear of 1.
the top panel.
Open front door and release the Cams located in the
2.
upper corner of both side panels.
! NOTE: To release Cams ensure arrow on Cam is facing
up.
arrow