Partner Tow spreader 2013 - Manual (Page 9)

9
Safety information
Read the safety information and
operating instructions
Before using the spreader for the
first time, please read the following
information in order to avoid danger to
persons, animals and property
– all safety information set out here,
– all the operating instructions.
For spreaders that are towed behind a
vehicle:
– safety information and operating
instructions that apply to the towing
vehicle.
Make sure
– that you yourself are familiar with all
relevant safety information,
– that all users of the spreader are
familiar with this information and
have understood it.
Injury hazard
Do not use the spreader to transport
people.
Wear sturdy footwear and protective
goggles when working with the
spreader.
Before using the spreader for the first
time, ensure that you are completely
familiar with the functions of the
towing vehicle.
The towing vehicle performs differently
when it is pulling a load.
– Do not drive too close to ditches or
other obstacles.
– Do not drive on steep inclines.
Always begin in 1st gear and never go
faster than 9.5 k.p.h.
Children are often attracted to tractors
and trailers. Never allow children to
handle this unit.
Using the spreader for its
intended purpose
The spreader should only be
used in the manner described in
these operating instructions and in
observance of the corresponding
safety information.
The spreader can only be operated in
conjunction with a suitably motorised
towing vehicle. The braking and
towing capacities of the towing vehicle
must be capable of handling the extra
load.
The spreader is not intended for use
on public paths or highways.
Operating procedure,
adjustments
Adjusting the spreading rate
– Estimate area to be treated.
Calculate the amount of material
to be distributed according to the
details on the packaging for the
spreading material.
– Set the spreader lever to OFF and
pour the product to be spread into
the hopper.
Notes on the substance to be used:
– Do not use powdered lime. Only use
granular products.
– Break up any clumps in the hopper.
– Determine the spreading rate
according to the following table.
Notes on figures in table:
The higher the number on the
adjustment scale, the larger the
opening in the base of the hopper.
The spreading rate depends upon
atmospheric humidity and the
moisture content of the substance to
be spread. It may be necessary to
adjust the minimum volumes shown in
the table to compensate for moisture.
The speed at which the spreader
travels affects the density of product
spread over a given area as well as
the width of the path covered.
– Loosen the Wing nut, set the
required spreading rate and then
Substance Form Setting for 5
k.p.h.
light heavy
Fertiliser Granular 3 5
Pelleted 3 5
Grass seed Fine 3 4
Coarse 4 5
De-icing agent 6 8
OIL
GREASE
CLIP CLIP
tighten the Wing nut again.
Spreading procedure
– Set the spreader in motion first,
before moving the spreader lever to
the ON position.
– Always move this lever to OFF
before the spreader comes to a
standstill.
Note:
In order to achieve complete coverage
of the area over which spreading is
carried out, maintain a distance of 2 to
2.5 m between the lines along which
the spreader travels.
Cleaning and care
After work has ended
– Empty out any residual spreading
substance from the hopper.
– Clean the spreader with water.
– Store the spreader in clean, dry
room.
Yearly lubrication of the spreader
1.
Remove the three clips from
the gear box and separate the
gearbox housings.
2. Lightly apply automotive grease
as needed to the gears.
3. Lightly oil the top of the gear box
and the vertical spreader shaft.
4. Re-assemble the gearbox
housings and secure them with
the clips.
5. Oil the (idler) wheel and the axle
bearings at least once a year or
more often as needed.
English