Marantz UD8004 - Manual (Page 11)

Troubl
eshooting
Information
HDMI
Control
Function
Pl
ayback
Setup
Connections
Specifications
ENGLISH
Inserting the Batteries
About the Remote Control Unit
e · Put·the·rear·cover·back·on.
q · Remove· the· remote· control·
unit’s·rear·cover.
w · Set·three·AAA/R03·batteries·in·
the·battery·compartment·in·the·
indicated·direction.
NOTE
Use·AAA/R03·batteries·in·this·remote·control.·
Replace· the· batteries· with· new· ones· if· the· set· does· not· operate·
even· when· the· remote· control· unit· is· operated· close· to· the· unit.·
(The·supplied·batteries·are·only·for·verifying·operation.)
When·inserting·the·batteries,·be·sure·to·do·so·in·the·proper·direction,·
following·the·“q”·and·“w”·marks·in·the·battery·compartment.
To prevent damage or leakage of battery fluid:
Do·not·use·a·new·battery·together·with·an·old·one.
Do·not·use·two·different·types·of·batteries.
Do·not·attempt·to·charge·dry·batteries.
Do·not·short-circuit,·disassemble,·heat·or·dispose·of·batteries·in·
flames.
If the battery fluid should leak, carefully wipe the fluid off the inside
of·the·battery·compartment·and·insert·new·batteries.
Remove·the·batteries·from·the·remote·control·unit·if·it·will·not·be·in·
use·for·long·periods.
Used·batteries·should·be·disposed·of·in·accordance·with·the·local·
regulations·regarding·battery·disposal.·
•
•
•
•
•
•
•
Operating Range of the Remote Control
Unit
Point·the·remote·control·unit·at·the·remote·sensor·when·operating·
it.
30° 30°
Approx.·16.4·ft·(5·m)
NOTE
The·set·may·function·improperly·or·the·remote·control·unit·may·not·
operate· if· the· remote· control· sensor· is· exposed· to· direct· sunlight,·
strong artificial light from an inverter type fluorescent lamp or infrared
light.
Remote Control Settings (Remote
Control Side)
Switches when the UD8004’s remote control operates another
MARANTZ BD players in the vicinity.
Set·the·remote·control·code·simultaneously·on·the·main·unit,·too.·
For· how· to· set· codes,· see· GUI· menu:· “Other· Setup”· –· “Remote·
Control·Setting”·–·“Remote·ID”·(vpage·30).
G Remote control code settingH
The·supplied·remote·control·has·two·remote·control·code·settings:·
BD·1·and·BD·2.
The·code·is·set·to·“BD·1”·at·the·factory.
To· set· the· code· to· “BD· 2”,· hold· the· stop· (
)· button· and· the·
Number·button·( ) pressed for more than five seconds.
To·set·(return)·the·code·to·“BD·1”,·hold·the·stop·( )·button·and·
the·Number·button·( ) pressed for more than five seconds.
If·the·signal·code·of·the·remote·control·does·not·match·the·signal·
code·of·the·unit,·the·remote·control·code·set·on·the·unit·is·shown·
on·the·display.
G
ExampleH
If· the· code· setting· on· the· unit· is· “BD· 1”,· and· the· setting· on· the·
remote·control·is·“BD·2”,·“BD·1”·is·shown·on·the·display.
NOTE
Match·the·signal·code·of·the·remote·control·with·the·signal·code·of·
the·unit.·If·the·remote·control·code·is·different,·you·cannot·operate·
the·UD8004·with·the·remote·control.
•
•
•
•
•
Getting Started