Marantz NR1403U - Manual (Page 64)

61
Audyssey
Default settings are underlined.
Set Audyssey MultEQ®, Audyssey Dynamic EQ® and Audyssey Dynamic Volume®. These can be
selected after Audyssey® Setup has been performed. For additional information on Audyssey technology,
please see
page 89 .
NOTE
• If you have not performed Audyssey® Setup, or if you change the speaker settings after performing
Audyssey® Setup, you may not be able to select Dynamic EQ®/Dynamic Volume®.
In this case, either perform Audyssey® Setup over again or perform “Restore...” (
vpage 27 ) to
return to the settings after Audyssey® Setup was run.
• When HD Audio for which the sampling frequency exceeds 96 kHz is played back, the “Audyssey”
cannot be set.
Setting items Setting details
MultEQ®
MultEQ® compensates for
both time and frequency
characteristics of the
listening area based on
Audyssey® Setup
measurement results.
Selection is done from three
types of compensation
curves. We recommend the
“Audyssey” setting.
MultEQ® is the prerequisite
function for Dynamic EQ®
and Dynamic Volume®. Audyssey : Optimize the frequency response of all speakers.
Audyssey Byp.L/R : Optimize frequency response of speakers except
front L and R speakers.
Audyssey Flat : Optimize frequency response of all speakers to flat
response.
Manual EQ : Apply frequency response set with “Manual EQ”
(
vpage 63 ).
Off : Turn “MultEQ®” equalizer off.
• “Audyssey”, “Audyssey Byp. L/R” and “Audyssey Flat” can be
selected after Audyssey® Setup has been performed. “Audyssey”
is automatically selected after performing Audyssey® Setup. When
“Audyssey”, “Audyssey Byp. L/R” or “Audyssey Flat” is selected,
illuminates.
• After running Audyssey® Setup, if the Speaker Configuration, Distance,
Channel Level, and Crossover Frequency have changed without
increasing the number of speakers measured, only
illuminates.
• This can also be set by pressing MultEQ .
Each time MultEQ is pressed, the setting is
changed as shown below.
Audyssey Audyssey Byp.L/R
Audyssey Flat Manual EQ Off
NOTE
When using headphones, “MultEQ®” is automatically set to “Off”.
“MultEQ®”, “Dynamic EQ®” and “Dynamic Volume®” settings are stored for each input source.
Audio
Audio Delay
Default settings are underlined.
While viewing video, manually adjust the time to delay audio output.
Setting details
0ms – 200ms
• This item can be set within the range of 0 to 100 ms when “Auto Lip Sync” ( vpage 65 ) is set to
“On” and when a TV compatible with Auto Lip Sync is connected.
• Store “Audio Delay” for each input source.
Volume
Default settings are underlined.
Set the volume setting.
Setting items Setting details
Scale
Set how volume is
displayed. 0 – 98 : Display in the range 0.5 (Min) to 98.
–79.5dB – 18.0dB : Display ---dB (Min), in the range –79.5 dB to 18.0 dB.
The “Scale” setting is applied also to the “Limit” and “Power On
Level” display method.
Limit
Make a setting for
maximum volume. Off : Do not set a maximum volume.
60 (–20dB) / 70 (–10dB) / 80 (0dB)
Power On Level
Define the volume setting
that is active when the
power is turned on. Last : Use the memorized setting from the last session.
Mute : Always use the muting on condition when power is turned on.
1 – 98 (–79dB – 18dB) : The volume is adjusted to the set level.
Mute Level
Set the amount of
attenuation when muting
is on. Full : The sound is muted entirely.
–40dB : The sound is attenuated by 40 dB down.
–20dB : The sound is attenuated by 20 dB down.
Basic v
ersion
A
dv
anced v
ersion
Inf
or
mations
A
dv
anced v
ersion
v See overleaf
DVD