Insinger Commander 18-6 - Manual (Page 4)

PART 1 TECHNICAL INFORMATION
DoorTypeTM2013 www.insingermachine.com 800-344-4802
COMMANDER 18-6
Automatic Single Tank Door Type Dishwasher
SPECIFICATIONS
CONSTRUCTION - Hood and tank constructed of 16 gauge type
304 S/S. Hood unit of all welded seamless construction. S/S
frame, legs and feet. All internal castings are non-corrosive lead
free nickel alloy or bronze.
DOORS - Three (both sides and front) simultaneously opening
doors. Operating doors have fingertip control, balanced by
externally mounted springs. (Corner installations have two
simultaneously opening doors at right angles.) All doors have
easy-glide strips. Extra large die formed type 304 S/S doors ride
in all S/S channels. A triple ply leading edge on the door channels
made of S/S.
PUMP - Centrifugal type “packless” pump with a brass petcock
drain. Construction includes ceramic seal and a balanced cast
impeller on a precision ground stainless steel shaft, extension or
sleeve. All working parts mounted as an assembly and removable
as a unit without disturbing pump housing. One 1 hp motor,
standard horizontal C-face frame, drip proof, internally cooled
with ball-bearing construction.
CONTROLS - Top mounted control cabinet, NEMA 12 rated,
housing motor controls and overload protection, transformer,
contactors and all dishwasher integral controls. Integrated rack
sensing system.
SPRAY SYSTEM - Wash and rinse spray systems made of type
304 stainless steel pipe threaded into cast hub assemblies.
Upper and lower wash and rinse spray assemblies are removable
without the use of tools.
WASH - 2 power spinning wash arms above and 2 power spinning
wash arms below. On top, each wash arm is designed with 8
nozzles (16 total). On the bottom, each wash arm is designed with
4 slots (8 total). The slots are precision milled for water control
and produce a fan spray.
FINAL RINSE - 2 power spinning rinse arms above and 2 power
spinning wash arms below. On top, each rinse arm is designed
with 2 nozzles (4 total). On the bottom, each rinse arm is
designed with 4 nozzles (8 total). The nozzles produce a fan spray
reducing water consumption, maximizing heat retention.
DRAIN - Drain valve externally controlled. Overflow assembly with
skimmer cap is removable without the use of tools for drain line
inspection. Heater is protected by low water level control.
Capacity Per Hour 65 racks
1625 dishes
80-160 meals
Tank Capacity 6.4 gallons
Motor Size 1 hp (wash)
Electric Usage 5.0 Kw 208v
5.0 Kw 240v
5.0 Kw 380v
5.0 Kw 480v
Built-in booster 40° - 70° rise
10.1 Kw 208v
13.5 Kw 240v
13.5 Kw 380v
13.5 Kw 480v
6.0 Kw remote booster 40° rise
12.0 Kw remote booster 70° rise
Steam Consumption
at 20 psi min.
11 lbs./hour tank
22 lbs./hour booster 40° rise
43 lbs./hour booster 70° rise
Final Rinse Peak Flow
at 20 psi min.
4.36 gallons/minute
Final Rinse Consumption
at 20 psi min.
47 gallons/hour
0.72 gallons/rack
Exhaust Hood Requirement 500 cfm
Peak Rate Drain Flow 9 gallons/minute
Shipping Weight 400 lbs.
Current Draw Amps
208/1/60
240/1/60
208/3/60
240/3/60
480/3/60
380/3/50
Steam
9.3
8.1
5.1
4.2
2.3
2.8
Electric w/o
booster
33.3
28.9
19
16.2
8.3
10.4
Electric w/
built-in booster
81.9
85.2
47
48.7
24.5
30.9
Note: Due to product improvement we reserve the right to change information
and specifications without notice.
4_2013
6245 State Road • Philadelphia, PA 19135 • PH: 800-344-4802 • FX: 215-624-6966 • www.insingermachine.com
2
®