Install interconnect cable to max200 b-4, Figure 1b-3, Inside rear of max200 power supply b-4 – Hypertherm THC2 Torch Height Control User Manual
Page 20: Installation - max200, Thc-2 torch height control, Install interconnect cable to max200
Page 1b-4
THC-2 Torch Height Control
INSTALLATION - MAX200
INSTALL INTERCONNECT CABLE TO MAX200
Strain Relief
R4
TB4
TB3
Figure 1b-3 Inside Rear of MAX200 Power Supply
1.
Connect the interface cable to RECP2 on the THC-2 module.
2.
Loosen the adjustable strain relief on the rear of the MAX200 power supply - Fig. 1b-3.
3.
Thread the other end of the interface cable through this strain relief and make
connections to TB4, TB3 (Fig. 1b-3) and voltage divider as shown in the Figure 1b-4
wiring diagram. Note: Push wires labeled 42 and 70 through the center wall feed-thru to
get to voltage divider.
4.
Connect the white wire from the voltage divider to location #45 on R4 which is located on
the left rear wall of the MAX200 power supply - Fig. 1b-4.
This completes installation of the THC-2 to the MAX200. See Section 2 for operation
instructions.
- EDGE Pro Ti Shape Cutting Control Rev.2 (288 pages)
- 80669J Rev.3 (304 pages)
- HD3070 Plasma Arc Cutting System w/ Manual Gas Console (281 pages)
- MAXPRO200 Rev.2 (294 pages)
- MicroEDGE Pro Shape Cutting Control Rev.2 (182 pages)
- Powermax1650 (317 pages)
- HPR260 Auto Gas Preventive Maintenance Program Rev.4 (288 pages)
- Shape Cutting Control (66 pages)
- PHC Sensor (58 pages)
- HTA Rev 6.00 Operators Manual (212 pages)
- HTA Rev 7.00 Install Guide (242 pages)
- THC Control Board Replacement (13 pages)
- THC Plasma Interfacer Upgrade (9 pages)
- THC X-Y Table Product Configuration (20 pages)
- D845GERG2 (128 pages)
- MRT2 (64 pages)
- MRT (98 pages)
- Duramax Hyamp Long Handheld Torches (92 pages)
- Duramax Hyamp Robotic Torch (74 pages)
- HyIntensity Fiber Laser Rev.3 (240 pages)
- PCBS-0124 (70 pages)
- SuperMicro 370SBA 533Mhz (90 pages)
- LR2075 (56 pages)
- Phoenix 8.0 (585 pages)
- LH2125 (60 pages)
- HD3070 w/ Automatic Gas (35 pages)
- HD3070 w/Manual Gas (43 pages)
- HD4070 Rev.8 (278 pages)
- HD4070 Product Configuration (88 pages)
- HPR800XD Manual Gas Preventive Maintenance Program Rev.1 (32 pages)
- HPR800XD Manual Gas Preventive Maintenance Program Rev.1 (33 pages)
- HPR800XD Manual Gas Rev.2 (368 pages)
- HPRXD Short Torch with Integrated Lead Rev.1 (30 pages)
- HT4001 (59 pages)
- DuraChill 5 HP Air-Cooled Chiller For Hypertherm (29 pages)
- HT4001 Air Injected Water Muffler System (40 pages)
- H601 Power Supplies (62 pages)
- MAX200 Remote Switch (9 pages)
- HT4100 Plasma Arc Cutting System Operating (50 pages)
- HT4001 Plasma Arc Cutting System (259 pages)
- HSD130 HySpeed Plasma (233 pages)
- HySpeed HT2000 Plasma Arc Cutting System Rev.7 (53 pages)
- HySpeed HT2000 Plasma Arc Cutting System Rev.27 (289 pages)
- MAX200 Water Muffler (39 pages)
- HT2000LHF Product Configuration (23 pages)