Install the thc-2 control module -2, Mount the thc-2 control module -2, Figure 1-1 – Hypertherm THC2 Torch Height Control User Manual
Page 10: Thc-2 control module mounting dimensions -2, Installation - to cutting machine & torch lifter, Thc-2 torch height control, Install the thc-2 control module
Page 1-2
THC-2 Torch Height Control
INSTALLATION - To Cutting Machine & Torch Lifter
FRONT
Figure 1-1 THC-2 Control Module Mounting Dimensions
17-3/32"
15-5/8"
6-3/4"
8"
5/8"
8-32
Tapped
Hole (3)
Bottom
View
INSTALL THE THC-2 CONTROL MODULE
Before installing the THC-2 system, verify the following components after unpacking:
•
Voltage Divider
•
THC-2 Control Module
•
Interconnecting cable #023264 (Cable not available for PAC-500 systems)
Mount the THC-2 Control Module
1.
Mount the THC-2 Control Module in a convenient location for the operator. See Fig.1-1
for mounting dimensions. Note the length of the control cable (5 feet) that will connect
from the THC-2 to the inside of the MAX100, MAX100
D
, or MAX200 and make certain
that the cable will reach before mounting. Customers must supply and fabricate cables
for the PAC-500 systems.
- EDGE Pro Ti Shape Cutting Control Rev.2 (288 pages)
- 80669J Rev.3 (304 pages)
- HD3070 Plasma Arc Cutting System w/ Manual Gas Console (281 pages)
- MAXPRO200 Rev.2 (294 pages)
- MicroEDGE Pro Shape Cutting Control Rev.2 (182 pages)
- Powermax1650 (317 pages)
- HPR260 Auto Gas Preventive Maintenance Program Rev.4 (288 pages)
- Shape Cutting Control (66 pages)
- PHC Sensor (58 pages)
- HTA Rev 6.00 Operators Manual (212 pages)
- HTA Rev 7.00 Install Guide (242 pages)
- THC Control Board Replacement (13 pages)
- THC Plasma Interfacer Upgrade (9 pages)
- THC X-Y Table Product Configuration (20 pages)
- D845GERG2 (128 pages)
- MRT2 (64 pages)
- MRT (98 pages)
- Duramax Hyamp Long Handheld Torches (92 pages)
- Duramax Hyamp Robotic Torch (74 pages)
- HyIntensity Fiber Laser Rev.3 (240 pages)
- PCBS-0124 (70 pages)
- SuperMicro 370SBA 533Mhz (90 pages)
- LR2075 (56 pages)
- Phoenix 8.0 (585 pages)
- LH2125 (60 pages)
- HD3070 w/ Automatic Gas (35 pages)
- HD3070 w/Manual Gas (43 pages)
- HD4070 Rev.8 (278 pages)
- HD4070 Product Configuration (88 pages)
- HPR800XD Manual Gas Preventive Maintenance Program Rev.1 (32 pages)
- HPR800XD Manual Gas Preventive Maintenance Program Rev.1 (33 pages)
- HPR800XD Manual Gas Rev.2 (368 pages)
- HPRXD Short Torch with Integrated Lead Rev.1 (30 pages)
- HT4001 (59 pages)
- DuraChill 5 HP Air-Cooled Chiller For Hypertherm (29 pages)
- HT4001 Air Injected Water Muffler System (40 pages)
- H601 Power Supplies (62 pages)
- MAX200 Remote Switch (9 pages)
- HT4100 Plasma Arc Cutting System Operating (50 pages)
- HT4001 Plasma Arc Cutting System (259 pages)
- HSD130 HySpeed Plasma (233 pages)
- HySpeed HT2000 Plasma Arc Cutting System Rev.7 (53 pages)
- HySpeed HT2000 Plasma Arc Cutting System Rev.27 (289 pages)
- MAX200 Water Muffler (39 pages)
- HT2000LHF Product Configuration (23 pages)