Hypertherm DuraChill 5 HP Air-Cooled Chiller For Hypertherm User Manual
Page 11
- 11 -
4.6 Startup
IMPORTANT: Be sure to turn main power Off before filling the reservoir.
4.6.1
Process Coolant
Use
only
Hypertherm Premixed Coolant = Part No.: 028872
69.9% Distilled Water, 30% Polypropylene Glycol, 0.1% Benzotriazole
Provides freeze protection to -12ºC (10ºF).
Do not use flammable fluids as a fire hazard may result.
WARNING: Coolant freeze protection must be 14ºC (25ºF) below the lowest possible
display temperature. The lowest possible display temperature is equal to the process
setpoint minus the Lower Band “Lb” setting.
If additional freeze protection is required, use 100% glycol to achieve required mixture.
Hypertherm 100% Glycol = Part No.: 028873
Filling the Reservoir
See Figure 4-2.
Remove the panel from the rear left side of the enclosure. It is held in place with 1/4-20 Philips head captive screws.
Remove the filler cap from the reservoir and fill it to a level approximately 2 inches (5.1 cm) from the top of the
reservoir. Do not replace the cap at this time.
- EDGE Pro Ti Shape Cutting Control Rev.2 (288 pages)
- 80669J Rev.3 (304 pages)
- HD3070 Plasma Arc Cutting System w/ Manual Gas Console (281 pages)
- MAXPRO200 Rev.2 (294 pages)
- MicroEDGE Pro Shape Cutting Control Rev.2 (182 pages)
- HPR260 Auto Gas Preventive Maintenance Program Rev.4 (288 pages)
- Powermax1650 (317 pages)
- Shape Cutting Control (66 pages)
- PHC Sensor (58 pages)
- HTA Rev 6.00 Operators Manual (212 pages)
- HTA Rev 7.00 Install Guide (242 pages)
- THC Control Board Replacement (13 pages)
- THC Plasma Interfacer Upgrade (9 pages)
- THC X-Y Table Product Configuration (20 pages)
- D845GERG2 (128 pages)
- MRT2 (64 pages)
- MRT (98 pages)
- Duramax Hyamp Long Handheld Torches (92 pages)
- Duramax Hyamp Robotic Torch (74 pages)
- HyIntensity Fiber Laser Rev.3 (240 pages)
- PCBS-0124 (70 pages)
- SuperMicro 370SBA 533Mhz (90 pages)
- LR2075 (56 pages)
- Phoenix 8.0 (585 pages)
- LH2125 (60 pages)
- HD3070 w/ Automatic Gas (35 pages)
- HD3070 w/Manual Gas (43 pages)
- HD4070 Rev.8 (278 pages)
- HD4070 Product Configuration (88 pages)
- HPR800XD Manual Gas Preventive Maintenance Program Rev.1 (33 pages)
- HPR800XD Manual Gas Preventive Maintenance Program Rev.1 (32 pages)
- HPR800XD Manual Gas Rev.2 (368 pages)
- HPRXD Short Torch with Integrated Lead Rev.1 (30 pages)
- HT4001 (59 pages)
- HT4001 Air Injected Water Muffler System (40 pages)
- H601 Power Supplies (62 pages)
- MAX200 Remote Switch (9 pages)
- HT4100 Plasma Arc Cutting System Operating (50 pages)
- HT4001 Plasma Arc Cutting System (259 pages)
- HSD130 HySpeed Plasma (233 pages)
- HySpeed HT2000 Plasma Arc Cutting System Rev.7 (53 pages)
- HySpeed HT2000 Plasma Arc Cutting System Rev.27 (289 pages)
- MAX200 Water Muffler (39 pages)
- HT2000LHF Product Configuration (23 pages)