Initial installation, Setting time and date / auto clock, Setting time and date setting auto clock – Daewoo DCR-9120 User Manual

Page 11: Setting up the player

Setting time and date

Setting Auto clock

Setting up the player

Initial Installation

■ Switch the TV on.
■ You can also start "AUTO SET" in the SETUP "PR PRESET"

"AUTO SET".

■ To tune in new stations (manual tuning) and to enter station names see page 23-24.

LANGUAGE SET

ENGLISH
DEUTSCH
ITALIANO
ESPAÑOL
FRANÇAIS
NEDERLANDS

…/†:SELECT
OK:CONFIRM SETUP:END

COUNTRY SET

LUX

OTHERS

…/†:SELECT
OK:CONFIRM SETUP:END

SETUP:END

PLEASE WAIT...

CH 25

RF OUTPUT SET

0-9:SELECT(21-69)
OK:CONFIRM SETUP:END

CURRENT

CH 52

RECOMMENDED CH

You should see this picture the first time you switch on the TV and player.

Choose your language.

Then choose your country.
For selecting the country, refer to the followings.

OK for "AUTO SET!".

"AUTO SET" tunes in all the stations you can receive in your country and
sorts them in an order common for your country.
Clock is automatically set.

If other stations are positioned on near the current RF OUTPUT CH, the
guide message appears automatically.

The player recommends the optimal RF OUTPUT CH number automatically.

B: Belgium
D: Germany
DK: Denmark
E: Spain
GR: Greece

I: Italy
LUX: Luxembourg
N: Norway
NL: Netherlands
S: Sweden

SF: Finland
CH: Switzerland
TR: Turkey

Press the [OK] button to confirm the recommended PR.

Should you wish the stations to have the same numbers as those used on the
TV, follow the instructions in "Sorting programme locations" on page 24.

Else ...
exit the basic installation function and enjoy your player.

PLEASE CHANGE THE TV
CH TO 54.

IMPORTANT!

MANUAL SET

PR01 ARD

PR08 P-08

PR02 ZDF

PR09 P-09

PR03 P-03

PR10 P-10

PR04 P-04

PR11 P-11

PR05 MTV

PR12 ----

PR06 P-06

PR13 ----

PR07 P-07

PR14 ----

…/†:SELECT
OK:CONFIRM SETUP:END

• If you don´t see this picture, because you don´t use a SCART cable, search this

picture now (CH 52) with the station tuning functions of your TV set (see its user
manual).

•

In case of interference problems on CH 52, type in an
other transmission channel between 21 and 69 using
the number buttons.

Setting time and date / Auto clock

■ Press [VCR] button on the remote control to change into VCR Mode and follow the procedure below.

Call the player’s "SETUP",
choose "VCR SETUP", then "CLOCK SET".

Move to the position you want to change and type in the new
values.
Wait a few seconds after typing a one-digit number.

Store with [OK] button and exit with [SETUP] button.

CLOCK SET

0-9:SETUP (HOUR)

œ/√

:CORRECT SETUP:END

TIME - - : - -

DATE - - / - - /- - - -

CLOCK SET

0-9:SETUP (HOUR)

œ/√

:CORRECT

OK:CONFIRM SETUP:END

TIME 06:05

DATE 08/06/2002(SUN)

■

Auto Clock is only available for models with the VPS/PDC function (see page 50).

Some broadcasting stations may send the time and date along with the VPS/PDC data. The video will automatically use
this time and date during the initial setting up procedure during normal use, and every time you switch the video off at
the mains. If you find that this time and date is incorrect you can remove this feature by following the steps below
changing it to OFF mode, you will then have to manually set the time and date, see above.

AUTO CLOCK

ON
OFF

…/†:SELECT

OK:CONFIRM SETUP:END

VCR SETUP

CLOCK SET
LANGUAGE SET
RF OUTPUT SET
16:9 SET
OSD ON/OFF
AUTO CLOCK

…/†:SELECT

OK:CONFIRM SETUP:END

Installation