Greenheck Jib Crane Assembly Instructions for Vektor (472081) User Manual
Page 3

3
Jib Crane Assembly for Vektor
®
®
Step 5: Raise jib crane assembly by hand-lifting and
using jib crane hand winch until fully erect.
Step 6: Secure jib crane assembly to plenum at
connection point 2 using one 1 x 6.75 inch hitch pin
(D). Lock hitch pin in place with cotter pin (G). Make
sure jib crane is firmly attached to plenum.
Step 7: At bracket connection point 3 and facing
connection point 5, attach one support tube (F) at
connection point 3 on jib crane using one 1 x 4.75 inch
hitch pin (E). Lock hitch pin in place with cotter pin (G).
Spread support tube out and attach the loose end to
matching plenum connection point 5. Secure end with
1 x 4.75 inch hitch pin (E). Lock hitch pin in place with
cotter pin (G).
NOTE
Hand winch equipped with self-activating automatic
brake.
CAUTION
Do not stand under the jib crane as it is being raised
or lowered. Slack in the wound cable could cause
crane assembly to suddenly drop downward and
cause serious injury or death.
Connection Point 2
Connection Point 3
Hitch Pin (D)
Hitch Pin (E)
Cotter Pin (G)
Cotter Pin (G)
Connection Point 5
Hitch Pin (E)
Cotter Pin (G)
Post Assembly
Post Assembly
- VCD-40 Extension Pin Kit 316SS (475290) (2 pages)
- 331-2856, 332-2856 - Siemens 6 Actuator (454206) (2 pages)
- 331-2976, 332-2976 - Siemens 4 Actuator (454202) (2 pages)
- 331-4551, 332-4551 - Siemens 3 Actuator (454201) (2 pages)
- Adjustable Pressure Controller (468292) (3 pages)
- 7800 Series Relay Modules (12 pages)
- Standard Control - MSSC (476372) (4 pages)
- NFB Series Actuators External Mount (464236 IOM) (2 pages)
- GND Series External Mount (473723) (4 pages)
- Amplifier for 7800 Series Relay Module (8 pages)
- APEX Curbs (462831) (4 pages)
- AMD-xx-TD Transmitter (35 pages)
- Blade Seal Repalcement (HCDR Series) (1 page)
- VCD (463384) (12 pages)
- BAPI Zone Pressure Touch (ZPT) Sensor (6 pages)
- VCD (463384) (10 pages)
- Blade Seal Replacement (HCD Series) (2 pages)
- BR Series - Counterweight Adjustment (469420) (4 pages)
- Leakage Rated Ceiling Radiation Dampers (475063 IOM). (32 pages)
- Canopy Hoods (452413 IOM) (36 pages)
- Clean-Out Port Kit (472428) (1 page)
- Centrifugal (CSW, BIDW, AFDW), Industrial (IPA, IPO, IPW) and Filtered Supply (LSF) (463687) (12 pages)
- Close Indicator Switch for Fire Dampers (474050) (1 page)
- Concrete Floor with Steel Deck Supplement (463562) (1 page)
- CRD-3XX and CRD-7XX Series for SP fans (452832) (2 pages)
- VCD (463384) (8 pages)
- VCD (463384) (4 pages)
- Single Side Retaining Angle (52 pages)
- DG / DGX with Pilot Ignition (463555 IOM) (Pre-2008) (48 pages)
- DG / DGX with Direct Spark (470652) (40 pages)
- Digital Temperature Interlock (474750 IOM) (Pre November 2012) (8 pages)
- DGK (468695) (20 pages)
- DG / DGX with Pilot Ignition (463555 IOM) (Pre-2008) (52 pages)
- Double Gland Axle Seal Replacement (1 page)
- Dock Arm Kit (475367) (4 pages)
- Duct Heaters Series IDHB and IDHC (478052) (8 pages)
- EHH-601D, Channel Installation (474643) (10 pages)
- EHH-601D, Channel Installation with VCD-40 Damper (474644) (8 pages)
- EHH-601D, Flange/Sleeve Installation (474641) (8 pages)
- GM Series (468391) (4 pages)
- EHH-601D, Flange/Sleeve Installation with VCD-40 Damper (474642) (8 pages)
- El-O-Matic E and P Series (12 pages)
- Energy Recovery Filter Hood System (8 pages)
- ERV-582/120 Curbs (460988) (4 pages)
- ESD-635D, Chanel Installation (474639) (10 pages)