Greenheck Fabra Hood, Multi Section with Filters, throat length greater than 72 inches (471324) User Manual
Assembly instructions, Figure 2

®
Assembly Instructions
Step 1
Step 2
1
Fabra Hood • Form G
Step 1 Fabra hood Form G 471324
Figure 2 Fabra hood Form G 471324
Open the shipping crates and separate the parts
according to the size of the unit. (See Figure No. 1 on
attached "PARTS LIST")
Figure 2
Place the two BASE ENDS, BASE SIDES and
INTERMEDIATE HOOD SUPPORT ASSEMBLY in their
approximate relationship to each other. (See Figure 2)
Fasten together the BASE ENDS to the BASE SIDES
using three (3)
1
⁄
4
-20 fasteners per corner for 5 inch high
base and four (4)
1
⁄
4
-20 fasteners per corner for 12 inch
high base.
Note: Fasteners should be hand tightened
only until step 4. On some units where the difference
between the hood width and throat width is greater than
32 inches, a REINFORCING PLATE is required in the
corners of the BASE (See Figure 2, DETAIL "A") Now
bolt the BASE SIDES to the INTERMEDIATE ASSEMBLY,
using eight (8)
1
⁄
4
-20 fasteners per INTERMEDIATE
ASSEMBLY for 5 inch base and ten (10)
1
⁄
4
-20 fasteners
for 12 inch high base.
Document #471324
Fabra Hood • Form G
Multi-Section with Filters
Throat length greater than 72 inches
- VCD-40 Extension Pin Kit 316SS (475290) (2 pages)
- 331-2856, 332-2856 - Siemens 6 Actuator (454206) (2 pages)
- 331-2976, 332-2976 - Siemens 4 Actuator (454202) (2 pages)
- 331-4551, 332-4551 - Siemens 3 Actuator (454201) (2 pages)
- Adjustable Pressure Controller (468292) (3 pages)
- 7800 Series Relay Modules (12 pages)
- Standard Control - MSSC (476372) (4 pages)
- NFB Series Actuators External Mount (464236 IOM) (2 pages)
- GND Series External Mount (473723) (4 pages)
- Amplifier for 7800 Series Relay Module (8 pages)
- APEX Curbs (462831) (4 pages)
- AMD-xx-TD Transmitter (35 pages)
- Blade Seal Repalcement (HCDR Series) (1 page)
- VCD (463384) (12 pages)
- BAPI Zone Pressure Touch (ZPT) Sensor (6 pages)
- VCD (463384) (10 pages)
- Blade Seal Replacement (HCD Series) (2 pages)
- BR Series - Counterweight Adjustment (469420) (4 pages)
- Leakage Rated Ceiling Radiation Dampers (475063 IOM). (32 pages)
- Canopy Hoods (452413 IOM) (36 pages)
- Clean-Out Port Kit (472428) (1 page)
- Centrifugal (CSW, BIDW, AFDW), Industrial (IPA, IPO, IPW) and Filtered Supply (LSF) (463687) (12 pages)
- Close Indicator Switch for Fire Dampers (474050) (1 page)
- Concrete Floor with Steel Deck Supplement (463562) (1 page)
- CRD-3XX and CRD-7XX Series for SP fans (452832) (2 pages)
- VCD (463384) (8 pages)
- VCD (463384) (4 pages)
- Single Side Retaining Angle (52 pages)
- DG / DGX with Pilot Ignition (463555 IOM) (Pre-2008) (48 pages)
- DG / DGX with Direct Spark (470652) (40 pages)
- Digital Temperature Interlock (474750 IOM) (Pre November 2012) (8 pages)
- DGK (468695) (20 pages)
- DG / DGX with Pilot Ignition (463555 IOM) (Pre-2008) (52 pages)
- Double Gland Axle Seal Replacement (1 page)
- Dock Arm Kit (475367) (4 pages)
- Duct Heaters Series IDHB and IDHC (478052) (8 pages)
- EHH-601D, Channel Installation (474643) (10 pages)
- EHH-601D, Channel Installation with VCD-40 Damper (474644) (8 pages)
- EHH-601D, Flange/Sleeve Installation (474641) (8 pages)
- GM Series (468391) (4 pages)
- EHH-601D, Flange/Sleeve Installation with VCD-40 Damper (474642) (8 pages)
- El-O-Matic E and P Series (12 pages)
- Energy Recovery Filter Hood System (8 pages)
- ERV-582/120 Curbs (460988) (4 pages)
- ESD-635D, Chanel Installation (474639) (10 pages)