Flowserve V-370 R3 Edward Valves - Manual (Page 12)

EDWARD UNIVALVE USER INSTRUCTIONS ENGLISH 12-13
12
UNIVALVE MAINTENANCE TOOLS (continued)
VALVES WITH “B” PREFIX FIGURE NUMBERS
Size
Figure
Number 1,6
Tool Head
Assembly
Guide Bushing
For Carbon
Steeel Valves 3
Guide Bushing
For Stainless
Steel Valves
Bonnet
Torquing
Collar
Assembly
Replacement
Cutters 2
No. Of
Cutters
On Head
Assembly 4
Check
Valve
Adapter
Assembly
Torque
Group 5
1/2 B36XXX 876112 499563 499564 876745 - - 166933 N/A
3/4 B36XXX 876112 499563 499564 876745 - - 166933 N/A
1 B36XXX 876112 499563 499564 876745 - - 166933 N/A
1-1/4 B36XXX 876114 875923 494228 876746 876703 5 166934 B
1-1/2 B36XXX 876114 875923 494228 876746 876703 5 166934 B
2 B36XXX 876115 875925 875934 876749 876703 5 166935 D
2-1/2 B36XXX 876116 875927 875936 876749 876703 7 166936 E
3 B36XXX 876116 875927 875936 876749 876703 7 166936 E
4 B36XXX 876116 875927 875936 876748 876703 7 166939 E
1/2 B66XXX 876112 499563 499564 876745 - - 166933 N/A
3/4 B66XYX 876112 499563 499564 876745 - - 166933 N/A
1 B66XXX 876112 499563 499564 876745 - - 166933 N/A
1-1/4 B66XXX 876113 875922 875930 876746 876703 3 166934 A
1-1/2 B66XXX 876113 875922 875930 876746 876703 3 166934 A
2 B66XXX 876115 875925 875934 876749 876703 5 166935 D
2-1/2 B66XYX 876116 875927 875936 876748 876703 7 166939 E
3 B66XXX 876116 875927 875936 876748 876703 7 166939 E
4 B66XXX 876116 875927 875936 876748 876703 7 166939 E
1/2 B96XXX 876112 876772 876773 876746 - - 168554 N/A
3/4 B96XXX 876112 876772 876773 876746 - - 168554 N/A
1 B96XXX 876112 876772 876773 876746 - - 168554 N/A
1-1/4 B96XXX 876112 876772 876773 876746 - - 168554 N/A
1-1/2 B96XXX 876112 876772 876773 876746 - - 168554 N/A
2 B96XXX 876115 875925 875934 876748 876703 5 876683 C
2-1/2 B96XXX 876115 875925 875934 876748 876703 5 876683 C
3 B96XXX 876115 875928 875934 876748 876703 5 876683 C
4 B96XXX 876115 875925 875934 876748 876703 5 876683 C
Notes:
1. First three numbers indicate pressure class and bonnet seal;
remaining two numbers denote valve type and end configuration,
which have no effect on tool selection.
2. Where dashes are indicated, cutters cannot be replaced.
3. Low alloy steel valves use same tools as carbon steel valves.
4. Required for using bonnet torqueing collar and seal weld cutting
machine on check valves.
5. To be used to determine the number of impacts required to close
valves with impactor handles/handwheels (see page 19). “N/A”
indicates that the valve(s) have standard handwheel (non-impactor).
6. Four-digit figure number Univalves use different maintenance tools.
Please consult your Edward Valves sales representative.