Flowserve V-370 R3 Edward Valves - Manual (Page 10)

EDWARD UNIVALVE USER INSTRUCTIONS ENGLISH 12-13
10
UNIVALVE MAINTENANCE TOOLS (continued)
Size
Figure
Number 1,6
Tool Head
Assembly
Guide Bushing
For Carbon
Steeel Valves 3
Guide Bushing
For Stainless
Steel Valves
Bonnet
Torquing
Collar
Assembly
Replacement
Cutters 2
No. Of
Cutters
On Head
Assembly
Check
Valve
Adapter
Assembly 4
Torque
Group 5
1/2 361XX 876111 875920 875929 876744 - - 876678 N/A
3/4 361XX 876111 875920 875929 876744 - - 876678 N/A
1 361XX 876112 975920 875929 876745 - - 876679 N/A
1-1/4 361XX 876113 875922 875930 876746 876703 3 876680 B
1-1/2 361XX 876114 875921 875931 876746 876703 5 876680 A
2 361XX 876115 875924 875933 876747 876703 5 876681 D
2-1/2 361XX 876116 875926 875917 876748 876703 7 876683 E
3 361XX 876116 875926 875917 876748 876703 7 876683 E
4 361XX 876116 875927 875936 876750 876703 7 876684 E
1/2 362XX 876111 875920 875929 876744 - - 876678 N/A
3/4 362XX 876111 875920 875929 876744 - - 876678 N/A
1 362XX 876111 875920 875929 876744 - - 876679 N/A
1-1/4 362XX 876113 875922 875930 876746 876703 3 876680 B
1-1/2 362XX 876113 875922 875930 876746 876703 3 876680 B
2 362XX 876114 875923 875918 876746 876703 5 876681 A
2-1/2 362XX 876115 875925 875934 876749 876703 5 876682 D
3 362XX 876115 875925 875934 876749 876703 5 876682 D
4 362XX 876116 875927 875936 876750 876703 7 876684 E
1/2 661XX 876111 875920 875929 876744 - - 876678 N/A
3/4 661XX 876111 875920 875929 876744 - - 876678 N/A
1 661XX 876112 875920 875929 876745 - - 876679 N/A
1-1/4 661XX 876113 875922 875930 876746 876703 3 876680 B
1-1/2 661XX 876113 875922 875930 876746 876703 3 876680 B
2 661XX 876115 875925 875934 876749 876703 5 876682 D
2-1/2 661XX 876116 875927 875936 876750 876703 7 876684 E
3 661XX 876116 875927 875936 876750 876703 7 876684 E
4 661XX 876116 875927 875936 876750 876703 7 876684 E
VALVES WITH NO PREFIX IN FIGURE NUMBERS
Notes:
1. First three numbers indicate pressure class and bonnet seal;
remaining two numbers denote valve type and end configuration,
which have no effect on tool selection.
2. Where dashes are indicated, cutters cannot be replaced.
3. Low alloy steel valves use same tools as carbon steel valves.
4. Required for using bonnet torqueing collar and seal weld cutting
machine on check valves.
5. To be used to determine the number of impacts required to close
valves with impactor handles/handwheels (see page 19). “N/A”
indicates that the valve(s) have standard handwheel (non-impactor).
6. Four-digit figure number Univalves use different maintenance tools.
Please consult your Edward Valves sales representative.