DFI HD330-Q87 - Manual (Page 9)

www.dfi .com
9
Chapter 2 Hardware Installation
Chapter 2
Chapter 2 - Hardware Installation
Board Layout
Battery
SPI Flash
BIOS
2 1
26 25
COM4
COM3
1
ATX
Power
13
12 24
LPC 12
1 11
2
Mini PCIe
+12V
Power
1 5
4 8
CPU Fan
1 1
2 10
9 1
2 10
9
COM5 COM6 1
2
5
6
(JP3)
1
2
5
6 (JP14) ISL95820
Mini PCIe Signal
Select (JP15)
1
3 10
12
1 1
1
Nuvoton
NCT6106D
1 2
10 9
Parallel
1 2
10 9
DDR3_1 DDR3_3
DDR3_4 DDR3_2
Clear CMOS
Data (JP9)
1
1
System
Fan 1
Intel
Q87
ITE
IT8893E
Realtek
ALC886
S/PDIF 1
2
9
10
1
Front Audio
ASMedia
ASM1442
ASMedia
ASM1442
Buzzer
System Fan 2
1
1 2
5 6
1 2
5 6
(JP11)
(JP2)
Intel
WGI210AT
Intel
WGI217LM
PS/2 KB/MS
USB 8-9
USB 2.0
Socket LGA1150 COM2
COM1
COM2
COM1
DVI-I
HDMI
LAN 1
USB 0-1
USB 3.0
Line-in
Line-out
Mic-in RESET-SW
HDD-LED
RSVD 1 2
Front Panel
RSVD
1112 ATX-SW
PWR-LED
1 1
1
USB 0-1 Power
Select (JP5)
USB 4-5
USB 2.0
LAN 2
SATA 5 Mini PCIe Power Select (JP16)
1 1
2
9
10 USB 2-3 USB 6-7 USB 12-13
1
2
9
10
1
2
9
10
1
Chassis
intrusion
PCIe x4
PCI 1
PCI 2
PCIe x16
Digital I/O
1
2
19
1 1 (JP4)
(JP1)
Power-on
Select (JP10) 1 Standby
Power LED
SATA 1 SATA 0
1 1 1
(JP12) (JP13) (JP7)
DIO Power Select
(JP13)
DIO 11/13/15/17
Output State (JP7)
DIO 3/5/7/9
Output State (JP12)
USB 2-3/6-7
Power Select (JP8)
USB 12-13
Power Select
(JP17)
1
USB 4-5 Power
Select (JP6)
SATA 2.0
SATA 3.0
USB 2.0
PS/2 KB/MS Power Select (JP1)
USB 8-9 Power Select (JP4)
COM1 RS232/422/485
Select
COM2 RS232/422/485
Select
COM1 RS232/Power
Select
COM2 RS232/Power
Select
(JP2)
(JP11)
(JP3)
(JP14)
System Memory
Important:
Electrostatic discharge (ESD) can damage your board, processor, disk drives, add-in
boards, and other components. Perform installation procedures at an ESD workstation
only. If such a station is not available, you can provide some ESD protection by wear-
ing an antistatic wrist strap and attaching it to a metal part of the system chassis. If
a wrist strap is unavailable, establish and maintain contact with the system chassis
throughout any procedures requiring ESD protection.
Important:
When the Standby Power LED lights red, it indicates that there is power on the sys-
tem board. Power-off the PC then unplug the power cord prior to installing any de-
vices. Failure to do so will cause severe damage to the motherboard and components.
COM2 COM1
Standby
Power LED
Features
Rear I/O
Onboard I/O
Storage
Expansion
DDR3-2
DDR3-1
DDR3-4
DDR3-3
Channel A
Channel B
• The four DIMM sockets are divided into 2 channels:
Channel A - DDR3_1 and DDR3_2
Channel B - DDR3_3 and DDR3_4
• Supports DDR3 1333/1600MHz
• Supports dual channel memory interface
• Supports up to 32GB system memory