Denon DN-A7100 - Manual (Page 45)

41
ENGLISH
Surround contents
Command Reply from Slave
Surr. Mode
AUTO “SUR:00”
“SUR:x“
(x = ‘0’ ~’Z’)
STEREO “SUR:01”
DOLBY “SUR:02”
PL2xMOVIE “SUR:03”
PL2 MOVIE “SUR:04”
PL2xMUSIC “SUR:05”
PL2 MUSIC “SUR:06”
PL2xGAME “SUR:07”
PL2 GAME “SUR:08”
Dolby PROLOGIC “SUR:09”
EX/ES “SUR:0A”
VIRTUAL 6.1 “SUR:0B”
- -
DTS ES “SUR:0E”
NEO6 CINEMA “SUR:0F”
NEO6 MUSIC “SUR:0G”
Multi Ch. STEREO “SUR:0H”
CSII CINEMA “SUR:0I”
CSII MUSIC “SUR:0J”
CSII MONO “SUR:0K”
VIRTUAL “SUR:0L”
DTS “SUR:0M”
DD+ PL2x MOVIE “SUR:0O”
DD+ PL2x MUSIC “SUR:0P”
- -
SOURCE DIRECT “SUR:0T”
PURE DIRECT “SUR:0U”
UP “SUR:1”
DOWN “SUR:2”
Command Reply from Slave
Test Tone
(Force start/stop Test
Tone with Auto mode)
TOGGLE “TTO:0”
“TTO:1xy” (OFF),
“TTO:2xy” (ON, x= auto(0)/
manual(1), y= ch.)
OFF “TTO:1”
ON “TTO:2”
NEXT “TTO:3”
PREV “TTO:4”
Night Mode
TOGGLE “NGT:0”
“NGT:1”(OFF),
“NGT:2”(ON)
OFF “NGT:1”
ON “NGT:2”
Command Reply from Slave
Lip Sync.
VALUE
“LIP:0xxx” (xxx = value)
xxx = 000 (OFF),
xxx = 010,020,...190,200
(ms)
“LIP:xxx”
(xxx = Lip Sync. value)
xxx = 000 (OFF),
xxx = 010,020,...190.200 ms UP “LIP:1”
DOWN “LIP:2”
Tuner contents
Command Reply from Slave
Tuner Frequency
VALUE
“TFQ:0xxxxx”
(xxxxx = freq.)
“TFQ:xxxxx”
(xxxxx = Frequency)
if (xxxxx < 02000) band=AM;
else band=FM;
(ex.“08750” = FM87.50MHz)
UP “TFQ:1”
DOWN “TFQ:2”
Auto-UP “TFQ:3”
Auto-DOWN “TFQ:4”
Tuner Preset
VALUE “TPR:0ww”
“TPR:ww”
(ww = current preset nr.)
(ww = 01 ~ ??)
UP “TPR:1”
DOWN “TPR:2”
P-Scan start “TPR:3”
P-Scan stop “TPR:4”
Tuner mode
TOGGLE “TMD:0” “TMD:0”( - ),
“TMD:1” (MONO),
“TMD:2” (AUTO)
OFF(MONO) “TMD:1”
ON(AUTO) “TMD:2”
Tuner RDS
DISP “RDS:3”
ACK
PTY “RDS:4”
Tuner MEMO - “MEM:0” ACK
CLEAR - “CLR:0” ACK
Tuner Numeric keys
Key0,
Key1,
Key2,
Key3,
Key4,
Key5,
Key6,
Key7,
Key8,
Key9
“NUM:0” ,
“NUM:1” ,
“NUM:2” ,
“NUM:3” ,
“NUM:4” ,
“NUM:5” ,
“NUM:6” ,
“NUM:7” ,
“NUM:8” ,
“NUM:9”
ACK
Specifi c Commands
Command from Host Reply from Slave
Auto status feedback
(The product default is all auto
status feedback disabled.)
“AST:x” (x = ‘0’ ~ ’F’)
bit 3 : Layer 4 ( 1 = Enable, 0 = Disable)
bit 2 : Layer 3 ( 1 = Enable, 0 = Disable)
bit 1 : Layer 2 ( 1 = Enable, 0 = Disable)
bit 0 : Layer 1 ( 1 = Enable, 0 = Disable) same as
command defi ne