DigiTech GSP1101 - Manual (Page 47)

To.assign.Expression.Links.to.parameters.via.the.Effect.Edit.screen
From the Preset screen, press the Edit/Select knob twice. This takes you to the Preset
Edit screen.
Turn the Edit/Select knob to select the effect that contains the parameter you want
to assign to a link. For our example we will select the Wah effect.
Press the Edit/Select knob to access the Wah Effect Edit screen.
Turn the Edit/Select knob to select the parameter you want to assign to a link. For
our example we will select WAH PEDAL.
Press the Edit/Select knob to edit the parameter. This is the parameter edit screen
and the message “HOLD TO ADD LINK” will appear at the bottom
Press and hold the Edit/Select knob. (Note: If the HOLD message doesn’t appear on
a parameter edit screen, then that parameter can not be linked. This will occur with
Model Type parameters for the most part)
The “Linking WAH PEDAL” screen will be displayed and the “ASSIGN CONTROLLER”
menu will be highlighted. Press the Edit/Select knob. “Linking WAH PEDAL
CONTROLLER=NOT LINKED” will be displayed.
Use the Edit/Select knob to select which of the 16 Global Controllers or 2 LFOs you
want to control the parameter. For our example we will select “CONTROLLER=12
. Press the Back.button to return to previous menu.
The Wah Pedal parameter is now linked to be controlled by MIDI CC 7. You can now
adjust the parameter’s Min and Max ranges by entering the “MIN VALUE” and “MAX
VALUE” menus if you don’t want to use the parameter’s full range, which is the default.
Store these changes to the preset using the Store procedure if these changes are to be
recalled later.SEAMLESS TIME
Presets in the GSP1101 that use delays and reverbs can have their repeats and reverb tails
heard to completion even after changing to a new preset. This is referred to as a “Seamless”
preset change. Each preset can have a specified seamless time before the preset is no
longer heard. There are two settings that control seamless time: Hold Time and Ramp Time.
Hold Time is the time frame from when a preset has been changed until the Ramp Time
takes effect. Ramp Time is the time it takes to ramp the output of the previous preset to a
muted state (i.e. If the Hold Time is set to 1.0 second and Ramp Time is set to 1.0 second,
after a preset change, the previous preset’s delays and reverbs will be heard at full volume
for 1 second. At the 1 second point, the Ramp Time will take effect and the delay repeats
and reverb tails will be ramped to a muted state – 2 seconds total). To.set.up.Seamless.TimePress the Edit/Select knob twice to enter the preset edit screen.
Turn the Edit/Select knob until Seamless Time is highlighted and press the Edit/
Select knob. This will enter the Editing Seamless screen.
Use the Edit/Select knob to select Hold Time or Ramp Time and press the knob.
Adjustments to Hold Time range from 10ms – Infinity. Adjustments to Ramp Time 1.2.3.
4.5.6.7.8.9.10.1.
2.3.
4.GSP0 Owner’s ManualThe Edit Effects/Preset Screen Pages: 1 … 45 46 47 48 49 … 64 wrong Brand wrong Model non readable Sitemap
SEAMLESS TIME
Presets in the GSP1101 that use delays and reverbs can have their repeats and reverb tails
heard to completion even after changing to a new preset. This is referred to as a “Seamless”
preset change. Each preset can have a specified seamless time before the preset is no
longer heard. There are two settings that control seamless time: Hold Time and Ramp Time.
Hold Time is the time frame from when a preset has been changed until the Ramp Time
takes effect. Ramp Time is the time it takes to ramp the output of the previous preset to a
muted state (i.e. If the Hold Time is set to 1.0 second and Ramp Time is set to 1.0 second,
after a preset change, the previous preset’s delays and reverbs will be heard at full volume
for 1 second. At the 1 second point, the Ramp Time will take effect and the delay repeats
and reverb tails will be ramped to a muted state – 2 seconds total).
To.set.up.Seamless.Time
Press the Edit/Select knob twice to enter the preset edit screen.
Turn the Edit/Select knob until Seamless Time is highlighted and press the Edit/
Select knob. This will enter the Editing Seamless screen.
Use the Edit/Select knob to select Hold Time or Ramp Time and press the knob.
Adjustments to Hold Time range from 10ms – Infinity. Adjustments to Ramp Time
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
1.
2.
3.
4.
GSP0 Owner’s Manual
The Edit Effects/Preset Screen