Delta 17-990X - Manual (Page 10)

10
5. Re-install the ring (E) Fig. 9 (removed in STEP 1).
IMPORTANT: DO NOT push the ring (E) Fig. 9 all the way down
on the the raising rack (F). Make certain that the top of the raising
rack (F) is under the bottom of the ring (E) and that enough
clearance is available to allow the rack (F) to rotate around the
column. Tighten the set screw (D) with the supplied 3mm wrench.
Fig. 9
E D
S T110.53 -11 w [2.958 1.97l ]2.958 d4642.922 ]29421 10.9376tk[148 659.602 44 -13.25 39.75wn ou6TD-04ET(Attace set t266 Tadjusts unhe b6 T(K078 0 TD25 le the orm geno shaftT(G the botJT*-0.0187[(column. TigL thega0.00.018flat supp1.47all the way d4 71.579210.2865shaftT the set scr)17.7(ew (D) with the supp-1.47all the wa[(7TD-04ET(ThD) withato r) clampnhe b6 T(M078 0 TD22 6nle theho6 Ti0.2865D) withark (F) t266 Tb is et.17.7(ota[(8TD-04ET(Ins ra(F) t266 T(P1 1-2ef9m0 g2 r6nle theho6 Ti0.2865t266 Tb is et.17.7(ota[(9TD-04ET(ThD) withato r) t266 Tlos alev.23(Q078 0 TD23r6nle theho6 Ti0.2865fack (Ftk (F266 Tb is et.17.7(lied 3m8 T8.55T.6 74.)]TJET1 g345.728 765.8 T8.55T.6 74.)]TJET1 g345.728 765.6 176 -125.6 reW* n/GS18.2417 BT2.2510 0 126.6079 345.282 639.47 cm/Im15 DoQQq1 i 0 792 612 -792 re0 792 mW n0 792.06 612 -792 reW n0 G0 J 66T8.55T6.6 74.) d/GS1 gs344.728340702 l5T.637 .)]TJET1 g345.728 765.6 0702 l5T.637 .)]TJET1 g345.728 765.6 176 -125.6 reW* n/GS1 .059 -7BT261610 0 126.7079 345.282 639.47 cm/Im15 DoQQq1 i 0 792 612 -792 re0 792 mW n0 792.06 612 -792 reW n0 G0 J 0.0502 l5T6.637 .) d/GS1 gs344.7288 T832 389.69 m.)]TJET1 g345.728 765.8 T832 389.69 m.)]TJET1 g345.728 765.6 176 -125.6 reW* n/GS18.26 m5.654810 0 126.8079 345.282 639.47 cm/Im15 DoQQq1 i 0 792 612 -792 re0 792 mW n0 792.06 612 -792 reW n0 G0 J 66T832 382.69 m.) d/GS1 gs344.7283407026 389.637 .)]TJET1 g345.728 765.6 07026 389.637 .