Televes Avant 7, 6 In/1 Out FM-BIII/DAB-TB-U-U-U (790 MHz) - Manual (Page 11)

EN
11
Default configuration menu
The next menu is Default Configuration:
/ Modifies the parameter (YES/NO).
(short press) - Activates the cursor.
(long press) - Executes the selected option and returns to the main
menu.
(short press) - Changes to the PIN menu ignoring the changes.
(long press) - Saving and adjustment (ignoring DEFAULT
CONFIGURATION).
Procedure
Use / to select YES/NO, and confirm the action with the button. This will
load the default configuration and returns to the main menu.
Unit locking PIN menu
The following menu is Unit locking PIN:
/
Allows to increase or decrease each of the four digits of the password,
the first between 0 ..7 and the rest between 0 .. 9 (0000 .. 7999).
(short press) - Places the cursor on the digits to be modified.
(long press) - Enters the main menu and activates the locking.
(short press) - Changes to Filter Status menu.
(long press) - Saving and adjustment.
Procedure
The unit leaves the factory unlocked, to lock it you need to enter a four digit PIN
using this menu.
Press the button to activate the first digit that composes the PIN. Use /
buttons to select a number between 0 and 7. Press again the to activate the
second digit and repeat the previous process to select a number between 0 and
9. Repeat until you complete the code.
Once this code has been entered you must confirm it with a long press on the
button. From now on, you can see all the menus but you cannot change the
configuration of the unit and you cannot save / adjust it (not even with the
external reset button).
While it is locked, all the menus of the programming unit show
-
í
indicating
this state. To unlock the unit, you need to enter the PIN again in this menu
following the same procedure (enter code and then confirm with a long press
of the button) and the unit will be unlocked.
Load
default
settings?
NO
Load
default
settings?
NO
Load
default
settings?
YES
Load
default
settings?
NO
Load
default
settings?
NO
Load
default
settings?
YES
Load
default
settings?
NO
Load
default
settings?
NO
Load
default
settings?
YES
PASSWORD
0 0 0 0
PASSWORD
0 0 0 0
PASSWORD
6 0 0 0
PASSWORD
6 0 0 0
CONFIG FI
Aten: 7dB
EQ: 3dB
LNB: 13V/ON
PASSWORD
0 0 0 0
PASSWORD
0 0 0 0
PASSWORD
6 0 0 0
PASSWORD
6 0 0 0
CONFIG FI
Aten: 7dB
EQ: 3dB
LNB: 13V/ON
PASSWORD
0 0 0 0
PASSWORD
0 0 0 0
PASSWORD
6 0 0 0
PASSWORD
6 0 0 0
CONFIG FI
Aten: 7dB
EQ: 3dB
LNB: 13V/ON
PASSWORD
0 0 0 0
PASSWORD
0 0 0 0
PASSWORD
6 0 0 0
PASSWORD
6 0 0 0
CONFIG FI
Aten: 7dB
EQ: 3dB
LNB: 13V/ON
Example:
IF configuration menu in a password locked unit
(the status menu also informs of this locking)
Saving and Adjustment process
Press for more than three seconds from any of the menus/submenus and
the saving and adjustment process will begin. The display will indicate the
following information:
- Saving the configuration in EEPROM.
- Starting the adjustment.
- Configuration of the inputs.
- Previous scan (switch on of the powerings and automatic adjustment of the
input attenuators).
- UHF adjustment.
- Adjustment of each filter (with interaction of the user in the case of error).
- VHF adjustment (in the case it is not cut-off).
- FM adjustment (in the case it is not cut-off).
- Output attenuator adjustment.
- Adjustment of the highest channel programmed to a specific output level.
The errors regarding a high or low level are indicated by messages on the
display.
The adjustment can be attempted again by pressing the button quickly or
ignored by pressing the button quickly.
Examples:
Beginning of the saving and adjusting sequence.
Long press of the button
Adjusting UHF filters.
Adjusting filter 1.
Adjusting UHF filters.
Low level input signal.
Adjusting UHF filters.
Ignoring adjustment of filter 1 by short pressing on the
button.
Final result of the adjustment.
Filter: 1
Input signal
LOW LEVEL
Programming
and saving
parameters
...
Input power
and input
attenuator
adjust ...
UHF filters
automatic
adjustment
...
Adjusting
filter: 1
...
Skipping
filter: 1
...
Output level
automatic
adjustment
...
Adjusting
filter Vout
...
F1 F2 F3-
F4í F5í F6-
F7í F8í F9í
F0í VHFí FMí
Filter: 1
Input signal
LOW LEVEL
Programming
and saving
parameters
...
Input power
and input
attenuator
adjust ...
UHF filters
automatic
adjustment
...
Adjusting
filter: 1
...
Skipping
filter: 1
...
Output level
automatic
adjustment
...
Adjusting
filter Vout
...
F1 F2 F3-
F4í F5í F6-
F7í F8í F9í
F0í VHFí FMí
Filter: 1
Input signal
LOW LEVEL
Programming
and saving
parameters
...
Input power
and input
attenuator
adjust ...
UHF filters
automatic
adjustment
...
Adjusting
filter: 1
...
Skipping
filter: 1
...
Output level
automatic
adjustment
...
Adjusting
filter Vout
...
F1 F2 F3-
F4í F5í F6-
F7í F8í F9í
F0í VHFí FMí
Filter: 1
Input signal
LOW LEVEL
Programming
and saving
parameters
...
Input power
and input
attenuator
adjust ...
UHF filters
automatic
adjustment
...
Adjusting
filter: 1
...
Skipping
filter: 1
...
Output level
automatic
adjustment
...
Adjusting
filter Vout
...
F1 F2 F3-
F4í F5í F6-
F7í F8í F9í
F0í VHFí FMí
Filter: 1
Input signal
LOW LEVEL
Programming
and saving
parameters
...
Input power
and input
attenuator
adjust ...
UHF filters
automatic
adjustment
...
Adjusting
filter: 1
...
Skipping
filter: 1
...
Output level
automatic
adjustment
...
Adjusting
filter Vout
...
F1 F2 F3-
F4í F5í F6-
F7í F8í F9í
F0í VHFí FMí
STATUS INFO
Unit is
not adjusted
STATUS INFO
The unit
has password
PASSWORD
0 0 0 0
PASSWORD
0 0 0 0
PASSWORD
6 0 0 0
PASSWORD
6 0 0 0
CONFIG FI
Aten: 7dB
EQ: 3dB
LNB: 13V/ON