4 the rooms menu, 5 the analogue outputs menu, 6 the headphones menu – Naim Audio NAC-N 272 User Manual
Page 18: 7 the network settings menu, Set up
16
4.3.10 Rear Panel Digital Inputs
Parameter Options
Unstable Source:
Yes / No
Select No
unless the
preamplifier has problems locking to a
digital signal. Selecting Yes will enable
the unit to play unstable digital signals,
however sound quality will be slightly
degraded.
4.3.11 Rear Panel Analogue Inputs
Parameter Options
AV Fixed Volume: Yes / No
If No is
selected the
input will behave normally. If Yes is
selected the input will operate at a
fixed volume and the preamplifier
volume control will be disabled. This
enables the preamplifier to be used in
multi-channel AV systems with volume
control handled by the AV processor.
Take care when selecting AV Fixed
Volume.
Note: AV fixed volume is available on rear panel analogue
inputs only.
4.4 The Rooms Menu
The Rooms menu enables NAC-N
preamplifiers to broadcast audio
from their UPnP™, iRadio, or USB
inputs simultaneously to up to four
other Naim streamer products connected to the same home
network.
Note: The Rooms menu is only visible when the multiroom
input is enabled. See Section 4.3.4.
4.5 The Analogue Outputs
Menu
The Analogue Outputs menu
enables the preamplifier DIN and
RCA phono output maximum volume and balance to be set.
The volume and balance settings apply simultaneously to
both outputs.
Parameter Options
Max. Volume:
0 to 100 (adjust with handset
5
or
5
)
Balance:
-10 to +10 (adjust with handset
5
or
5
)
Outputs:
DIN / RCA / DIN+RCA
4.6 The Headphones Menu
The Headphones setup menu
enables the Max. Volume parameter
to be selected:
Parameter Options
Max. Volume:
0 to 100 (adjust
with handset
6
or
5
)
4.7 The Network Settings Menu
The Network Settings menu
enables network parameters to be
customised to suit the router and
network. The options are tabulated
and described in the following
sections:
Parameter Options
Name:
User definable. Use the handset or
Naim app to enter text.
Wireless:
Not Used / Wi-Fi Network Name
Status:
Connected / No Signal / Login Failure /
Busy / Etc.
DHCP:
Yes / No
MAC:
Displays the unit’s MAC address.
The Name parameter enables the preamplifier’s default
network name to be changed.
The Wireless parameter enables a wireless network to be
chosen and joined. See Section 4.7.1 below for detailed
wireless set up notes.
Network Status displays the current network connection
status.
The DHCP parameter enables the network settings to be
modified. In most cases leaving the option set to DHCP will
be the appropriate choice. See Section 4.7.2 below for notes
on non-DHCP network connection.
Note: Devices installed on a network have an IP address
through which they are identified by all the other items
on the network. DHCP is a set of rules that enable the
automatic allocation of addresses as items are connected
(or switched on while connected) to the network. All
NAC-N preamplifiers are configured by default to use
DHCP.
Note: If a NAC-N preamplifier is connected to a network
both wirelessly and via a wired connection, the wired
connection will take priority.
4. Set Up
Digital 1
4/4
Enabled:
Yes
Name:
Digital 1
Input Trim:
0
4
Unstable Source:
No
Analogue 1
4/4
Enabled:
Yes
Name:
Analogue 1
Input Trim:
0
4
AV Fixed Volume
No
Rooms 1/2
4a
Qute-3F65
Uniti-2E23
Network Settings
1/5
4
Name: 272-0131
Wireless:
Not Used
Status: Not Connected
DHCP
Yes
Headphones 1/1
4
Max. Volume:
100
Analogue Outputs
1/3
4
Max. Volume:
100
Balance:
0
Outputs
DIN+RCA