G-Shock DWG-100UJ-9JR - Manual (Page 3)

2059-3
About Stopwatch Memory
Whenever you perform a stopwatch operation, measured times are
automatically stored into memory along with the measurement date. You
can store up to 30 lap/split times in memory. If you perform more than 30
lap/split time operations, the memory will contain the times for the last 29
laps/splits (as lap/split numbers 1 through 29), and the final lap and split
time (as lap/split 30).
• Data in lap/split memory is cleared whenever you start a new
stopwatch operation.
• The final elapsed time, or final lap and split time is stored in memory
when you press
L to clear the stopwatch to all zeros.
Recalling Data from Memory
1. Use C to enter the Recall Mode.
•
The upper part of the display first shows
the measurement date followed by the
lap/split number, and then the oldest lap
time in memory. The lower part of the
display shows the split time.
2. Press B to scroll forward through the data
items or L to scroll backward.
• The message REC xx txx appears in
the upper display if you enter the Recall
Mode when there is no data stored in it.
Deleting the Data from Memory
To delete all data currently in memory, enter the Recall Mode and then
hold down
A until the message REC xx txx appears in the upper
display.
Measurement date
Lap/Split
number
Split time
Lap time
COUNTDOWN ALARM
The countdown timer can be set within a
range of 1 second to 24 hours. When the
countdown reaches zero, an alarm sounds.
•
Countdown alarm functions are available in
the Countdown Alarm Mode, which you can
enter using
C .
•
You can also select auto-repeat, which
automatically restarts the countdown from
the original value you set whenever zero is
reached.
Using the Countdown Timer
Press B while in the Countdown Alarm Mode to start the countdown timer.
•
When the end of the countdown is reached and auto-repeat is turned
off, the alarm sounds for 10 seconds or until you stop it by pressing
any button. The countdown time is automatically reset to its starting
value after the alarm stops.
Current time
Hours
Minutes
Seconds
• Press B while a countdown operation is in progress to pause it. Press
B again to resume the countdown.
•
To completely stop a countdown operation, first pause it (by pressing B ),
and then press L . This returns the countdown time to its starting value.
Setting the Countdown Time
1. In the Countdown Alarm Mode, hold down A until the hours digit of
the countdown time starts to flash.
2. Press C to move the flashing in the sequence shown below to select
other settings.
Seconds Hours Minutes
3. While hours, minutes, or seconds digits are flashing, press B to
increase the setting or L to decrease it.
• To set the starting value of the countdown time to 24 hours, set
0:00 00 .
4. Press A to return to the countdown alarm display screen.
Turning Auto-repeat On and Off
In the Countdown Alarm Mode, press L to
turn auto-repeat on (AUTO REPEAT
displayed) and off (AUTO REPEAT not
displayed).
• When the end of the countdown is reached
and auto-repeat is turned on, the alarm
sounds, but the countdown starts again
automatically whenever the countdown
reaches zero. You can stop timing by
pressing
B , and manually reset to the
starting countdown time by pressing L .
•
Normally, an alarm tone sounds for 10 seconds when the end of the
countdown is reached. If you use auto-repeat with start time of 10
seconds or less, the watch beeps once.
ALARM
You can set up to five independent alarms
with hour, minutes, month, and day. When the
alarm is turned on, the alarm tone sounds
when the time is reached.
You can also turn on an Hourly Time Signal
that causes the watch to beep twice every
hour on the hour.
• Alarm functions (and Hourly Time Signal
settings) are available in the Alarm Mode,
which you can enter using
C .
• The alarm number ( AL1 though AL5 )
indicates an alarm screen. SIG appears in
place of the alarm number when the Hourly
Time Signal screen is shown.
Month – Day
Hour : Minutes
Alarm on indicator
Alarm No.
Alarm Types
The alarm type is determined by the settings you make, as described
below.
• Daily alarm
Set the hour and minutes for the alarm time. This type of setting causes
the alarm to sound everyday at the time you set.
• Date alarm
Set the month, day, hour and minutes for the alarm time. This type of
setting causes the alarm to sound at the specific time, on the specific
date you set.
• 1-Month alarm
Set the month, hour and minutes for the alarm time. This type of setting
causes the alarm to sound everyday at the time you set, only during the
month you set.
•
Monthly alarm
Set the day, hour and minutes for the alarm time. This type of setting
causes the alarm to sound every month at the time you set, on the day
you set.
Setting an Alarm Time
1. In the Alarm Mode, press B to select the
alarm whose time you want to set.
2. After you select an alarm, hold down A until the hour digits of the
alarm time start to flash.
• This operation automatically turns on the alarm.
3. Press C to move the flashing in the sequence shown below to select
other settings.
AL1
SIG
AL2
AL5
AL3
AL4
Hour Day Minutes Month
4. While hour, minutes, month, or day is flashing, press B to increase
the setting or L to decrease it.
• To set an alarm that does not include a month (Daily alarm, Monthly
alarm), set
xx for the month. Press B or L until the xx mark
appears (between 12 and 1) while month setting is flashing.
• To set an alarm that does not include a day (Daily alarm, 1-Month
alarm), set
xx for the day. Press B or L until the xx mark
appears (between 31 and 1) while the day setting is flashing.
•
When setting the alarm time using the 12-hour format, take care to
set the time correctly as a.m. (
A indicator) or p.m. ( P indicator).
5. Press A to return to the alarm display screen.
Alarm Operation
The alarm sounds at the preset time for about 20 seconds, or until you
stop it by pressing any button.
To test the alarm
In the Alarm Mode, hold down
L to sound the alarm.
Turning an Alarm and the Hourly Time Signal On and Off
1. In the Alarm Mode, press B to select an alarm or the Hourly Time
Signal.
2. When the alarm or the Hourly Time Signal you want to is selected,
press L to turn it on and off.
Indicates alarm is on.
Indicates Hourly Time Signal is on.
• The alarm on indicator ( ) and the Hourly Time Signal on indicator
( ) are shown on the display in all modes while these functions are
turned on.
• If any alarm is on, the alarm on indicator is shown on the display
when you change to another mode.