G-Shock 2039 - Manual

2039-1
Module No.2039
ABOUT THIS USER’S GUIDE
Congratulations upon your selection of this CASIO watch. To get the most out of your purchase, be sure to carefully read this User’s Guide and keep it on hand for later reference when
necessary.
• Button operations are indicated using the letters shown in the illustration.
• This watch displays white figures on a black background, but all sample displays in this User’s Guide show black figures on a white background.
Alarm Mode Countdown Alarm Mode Stopwatch Mode
• Press C C C C C to change from mode to mode. After you perform an operation in any mode, pressing C C C C C returns to the Timekeeping Mode.
• Press E E E E E in any mode to illuminate the display.
GENERAL GUIDE
Timekeeping Mode
Press C C C C C .
TIMEKEEPING MODE
To set the time and date
1. Press A A A A A while in the Timekeeping Mode. The seconds
digits flash on the display because they are selected .
2. Press C C C C C to change the selection in the following se-
quence.
Seconds
Day
Hour Minutes
Year Month
3. While the seconds digits are selected (flashing), press
D D D D D to reset the seconds to 00 . If you press D D D D D while the
seconds count is in the range of 30 to 59, the seconds
are reset to
00 and 1 is added to the minutes. If the
seconds count is in the range of 00 to 29, the minutes
count is unchanged.
4. While any other digits (besides seconds) are selected (flashing), press D D D D D to
increase the number. Holding down D D D D D changes the number at high speed.
• To switch between the 12-hour and 24-hour formats, press E E E E E while some digits
are flashing.
5. After you set the time and date, press A A A A A to return to the Timekeeping Mode.
• The day of the week is automatically set in accordance with the date.
• The date can be set within the range of January 1, 1995 to December 31, 2039.
• If you do not operate any button for a few minutes while a selection is flashing, the
flashing stops and the watch goes back to the Timekeeping Mode automatically.
BACKLIGHT
The backlight uses an EL (electro-luminescent) panel that causes the entire display
to glow for easy reading in the dark. An EL alarm feature can be turned on so the
backlight flashes whenever an alarm or hourly time signal sounds.
• Pressing E E E E E in any mode illuminates the display for about two seconds, regardless
of the EL alarm on/off setting.
• The backlight of this watch employs an electro-luminescent (EL) light, which loses
its illuminating power after very long term use.
• Frequent use of the backlight shortens the battery life.
• The watch will emit an audible sound whenever the display is illuminated. It does not
indicate malfunction of the watch.
• The illumination provided by the backlight may be hard to see when viewed under
direct sunlight.
• The backlight automatically stops illuminating whenever an alarm sounds.
To turn the EL alarm on and off
In the Timekeeping Mode, hold down D D D D D for about two
seconds to toggle the EL alarm on ( displayed) and off
( not displayed).
• The EL alarm on indicator remains on the display in all
modes until you switch the EL alarm off.
• The above operation controls operation of the EL alarm
only. It does not affect operation of audible tones and
signals.
ALARM MODE
You can set an alarm with hour, minutes, month, and day.
When the alarm is on, the alarm sounds for 20 seconds at
the preset time. When the Hourly Time Signal is on, the
watch beeps every hour on the hour.
Alarm Types
The types of alarm you get depends on the information
you set.
• Daily alarm
Set the hour and minutes for the alarm time. Set
x for
the month and xx for the day (see step 3 under “To set
the alarm time”). This type of setting causes the alarm
to sound everyday at the time you set.
• Date alarm
Set the month, day, hour and minutes for the alarm time.
This type of setting causes the alarm to sound at the
specific time, on the specific date you set.
Minutes
Hour
Month – Day
Day of week
Seconds
PM indicator
EL alarm on indicator
Mode indicator
Hour Minutes
Month – Day
Hourly time signal on
indicator
Alarm on indicator
• 1-Month alarm
Set the month, hour and minutes for the alarm time. Set
xx for the day (see step
3 under “To set the alarm time”). This type of setting causes the alarm to sound
everyday at the time you set, only during the month you set.
• Monthly alarm
Set the day, hour and minutes for the alarm time. Set
x for the month (see step 3
under “To set the alarm time”). This type of setting causes the alarm to sound every
month at the time you set, on the day you set.
To set the alarm time
1. Press A A A A A while in the Alarm Mode until the hour digits start to flash on the display.
The hour digits flash because they are selected .
• At this time the alarm is automatically switched on.
2. Press C C C C C to change the selection in the following sequence.
Hour
Day
Minutes
Month
3. Press D D D D D to increase the selected digits. Holding down D D D D D changes the number at
high speed.
• The format (12-hour and 24-hour) of the alarm time matches the format you select
for normal timekeeping.
• When setting the alarm time using the 12-hour format, take care to set the time
correctly as morning (no indicator) or afternoon (P indicator).
4. After you set the alarm time, press A A A A A to return to the Alarm Mode.
• If you do not operate any button for a few minutes while a selection is flashing, the
flashing stops and the watch goes back to the Alarm Mode automatically.
To stop the alarm
Press any button to stop the alarm after it starts to sound.
To turn an alarm and Hourly Time Signal on and off
Press D D D D D while in the Alarm Mode to change the status of an alarm and Hourly Time
Signal in the following sequence.
[ Alarm ON Indicator/Hourly Time Signal ON Indicator ]
Hourly Time
Signal only Alarm Only Both OFF Both ON
COUNTDOWN ALARM MODE
The countdown timer can be set within a range of 1 second
to 24 hours. When the countdown reaches zero, an alarm
sounds.
• You can also select Auto-Repeat, which automatically
restarts the countdown from the original value you set
whenever zero is reached.
To set the countdown time
1. Press A A A A A while in the Countdown Alarm Mode. The hours
digit flashes on the display because it is selected .
2. Press C C C C C to change the selection in the following se-
quence.
Seconds Minutes Hours
3. Press D D D D D to increase the selected number. Holding down D D D D D changes the number at
high speed.
• To set the starting value of the countdown time to 24 hours, set to 0:00'00 .
4. After you set the countdown time, press A A A A A to return to the Countdown Alarm Mode.
• If you do not operate any button for a few minutes while a selection is flashing, the
flashing stops and the watch goes back to the Countdown Alarm Mode automatically.
To use the countdown timer
Press D D D D D while in the Countdown Alarm Mode to start the countdown timer.
• When the end of the countdown is reached and Auto-Repeat is turned off, the alarm
sounds for 10 seconds or until you stop it by pressing any button. The countdown time
is automatically reset to its starting value after the alarm stops.
• Press D D D D D while a countdown operation is in progress to pause it. Press D D D D D again to
resume the countdown.
• To completely stop a countdown operation, first pause it (by pressing D D D D D ), and then
press A A A A A . This returns the countdown time to its starting value.
Hours Seconds
Minutes
Current time
Mode indicator