beautypg.com

G-Shock GT-003TH-8BT User Manual

G-Shock Clock

background image

— 9 —

2-2. QW-1699

Press

M

to change from mode to mode.

A

M

L

B

C

Timekeeping Mode

Beat Counter Mode

Stopwatch Mode

Alarm Mode

GENERAL GUIDE

TIMEKEEPING MODE

To set the time and date

1. Hold down

A

while in the Timekeeping Mode until the

seconds digits start to flash on the display. The seconds
flash because they are

selected.

2. Press

M

to change the selection in the following

sequence.

3. While the seconds digits are selected (flashing), press

C

to reset the seconds to

00

.

If you press

C

while the seconds count is in the range of 30 to 59, the seconds are

reset to

00

and 1 is added to the minutes. If the seconds count is in the range of 00 to

29, the minutes count is unchanged.

4. While any other digits (besides seconds) are selected (flashing), press

C

to increase

the number. While the 12/24-hour setting is selected, press

C

to switch between the

two formats.

Holding down

C

changes the current selection at high speed.

When the 12-hour format is selected, the

12H

indicator appears on the display. With

the 12-hour format, the P (PM) indicator appears on the display to indicate “p.m.”
times. There is no indicator for “a.m.” times.

Selecting the 24-hour format causes the

24H

and the 24 indicators to appear on the

display.

5. After you set the time and date, press

A

to return to the Timekeeping Mode.

The day of the week is automatically set in accordance with the date.

The date can be set within the range of January 1, 1995 to December 31, 2039.

If you do not operate any button for a few minutes while a selection is flashing, the
flashing stops and the watch goes back to the Timekeeping Mode automatically.

A

M

M

B

Day of week

Month – Day

Seconds

PM indicator

Hour : Minutes

Seconds

Hour

Minutes

Day

Month

Year

12/24-Hour
Format

BACKLIGHT FUNCTION

A backlight that uses an EL (electro-lumunescent) panel
causes the entire display to glow for easy reading in the
dark. An auto light switch causes the EL backlight to turn on
when the watch is angled toward your face for reading. An
EL alarm feature can be turned on so the backlight flashes
whenever an alarm or hourly time signal sounds.

The auto light switch on indicator is shown on the display
in all modes while the auto light switch is on.

The FLASH indicator is shown on the display in all modes
while the EL alarm is on.

Note

The backlight of the watch employs an electro-luminescent
(EL) light, which loses illuminating power after very long
use.

The illumination provided by the backlight may be hard to see when viewed under
direct sunlight.

The watch will emit an audible sound whenever the display is illuminated. This is caused
by a transistor that vibrates when the EL panel lights up. It does not indicate malfunction
of the watch.

The backlight automatically turns off whenever an alarm sounds.

To manually turn on the backlight

Pressing

L

in the Timekeeping, Stopwatch or Alarm Mode causes the backlight to turn

on for about two seconds. Pressing

C

in the Beat Counter Mode also causes the backlight

to turn on for a fixed amount of time.

The backlight normally stays on for about two seconds and then turns off automatically.
When the EL alarm is turned on, however, the backlight stays on for about five seconds
instead of two seconds.

The above operations turn on the backlight, regardless of the current auto light switch
and EL alarm settings.

A

M

C

L

B

Auto light switch on indicator

FLASH indicator

To turn the EL alarm on and off

In the Timekeeping Mode, hold down

B

for about two seconds to toggle the EL alarm

on (FLASH indicator displayed) and off (FLASH indicator not displayed).

When the EL alarm is on, the backlight flashes while the daily alarm and hourly time
signal tones are sounding. Also, the backlight stays on for about five seconds instead
of the normal two seconds.

When an auto light switch operation causes the backlight to turn on while the EL alarm
is turned on, the backlight stays lit for about two seconds, and then flashes for two
seconds.

About the Auto Light Switch

While the auto light switch is turned on, the backlight automatically lights for about two
seconds whenever you position your wrist as described below. Avoid wearing the watch
on the inside of your wrist. Doing so causes the auto light switch to operate when it is not
needed, which shortens battery life.

Moving the watch to a position that is parallel to the ground and then tilting it towards
you more than 40 degrees causes the backlight to illuminate.

The backlight may not illuminate if the face of the watch is more than 15 degrees off
the parallel as shown below. Make sure that the back of your hand is parallel to the
ground.

Parallel to
ground

More than
40

°

Static electricity or magnetic force can interfere with proper operation of the auto light
switch. If the auto light switch does not illuminate, try moving the watch back to the
starting position (parallel with the ground) and then tilt it back toward you again. If this
does not work, drop your arm all the way down so it hangs at your side, and then bring
it back up again.

Under certain conditions the backlight may not light until about one second or less
after turn the face of the watch towards you. This does not necessarily indicate
malfunction of the backlight.

Warning!

Never try to read your watch when mountain climbing or hiking in areas that are
dark or in areas with poor footing. Doing so is dangerous and can result in
serious personal injury.

Never try to read your watch when running where there is danger of accidents,
especially in locations where there might be vehicular or pedestrian traffic. Doing
so is dangerous and can result in serious personal injury.

Never try to read your watch when riding on a bicycle or when operating a
motorcycle or any other motor cycle. Doing so is dangerous and can result in a
traffic accident and serious personal injury.

When you are wearing the watch, make sure that its auto light switch is turned
off before riding on a bicycle or operating a motorcycle or any other motor vehicle.
Sudden and unintended operation of the auto light switch can create a distraction,
which can result in a traffic accident and serious personal injury.

Parallel to ground

More than 15 degrees
too high

More than 15 degrees
too low

To turn the auto light switch on and off
In the Timekeeping Mode, hold down

C

for one second to turn the auto light switch on

(

displayed) and off (

not displayed).

In order to protect against running down the battery, the auto light switch is automatically
turned off approximately three hours after you turn it on. Repeat the above procedure
to turn the auto light switch back on if you want.

This manual is related to the following products: