G-Shock DWG-100UJ-9JR - Manual

2059-1
Module No. 2059
Congratulations upon your selection of this CASIO watch. To get the
most out of your purchase, be sure to carefully read this manual and
keep it on hand for later reference when necessary.
Warning!
•
The pulse measurement function built into this watch is not
intended for taking measurements that require professional or
industrial precision. Values produced by this watch should be
considered as reasonable representations only.
• CASIO COMPUTER CO., LTD. assumes no responsibility for any
loss, or any claims by third parties that may arise through the use
of this watch.
About this manual
• Button operations are indicated using the
letters shown in the illustration.
• Each section of this manual provides you
with the information you need to perform
operations in each mode. Further details
and technical information can be found in
the “REFERENCE” section.
• Press C to change from mode to mode.
• Pressing the P button enters directly into the Pulse Measurement
Mode from any other mode.
Stopwatch Mode
Press
C
.
Recall Mode
Countdown Alarm Mode Alarm Mode
▲
▲
▲
▲
▲
Pulse
Measurement
Mode
Press P .
Timekeeping Mode
▲
▲
Press C .
Setting the Time and Date
1. In the Timekeeping Mode, press B to
display the Date screen.
2. Hold down A until the seconds digits start
to flash.
3. Press C to move the flashing in the
sequence shown below to select other
settings.
4. While hour, minutes, year, month, or day is flashing, press B to
increase the setting or L to decrease it.
• While the seconds setting is selected, press B to reset seconds to
OO .
• When the 12/24-hour setting is selected, press B to toggle
between 12-hour ( 12H ) and 24-hour ( 24H ) timekeeping.
5. Press A to return to the current time screen.
TIMEKEEPING
Use the Timekeeping Mode to set and view the current time and date.
You can also display the current temperature.
• In the Timekeeping Mode, press B to toggle between the date screen
and temperature screen.
• See the section of this manual titled “THERMOMETER” for information
about the temperature screen.
▲
▲
[Date] [Temperature]
Day of week Month – Day
PM indicator Hour : Minutes Seconds
Press B .
Temperature
Hour Seconds
Day
Minutes
12/24-Hour
Format
Year Month
THERMOMETER
A built-in temperature sensor measures
temperature and shows the measured value
on the display. You can calibrate the
temperature sensor if you suspect the
temperature reading is incorrect.
Understanding the Temperature
Screen
1. Use C to enter the Timekeeping Mode.
2. Press B to display the Temperature
screen.
• Temperature is displayed in units of
0.1
° C in the range of –20.0 ° C to 60.0 ° C.
•
Press B again to return to the date
screen.
Temperature
About Temperature Measurements
•
When you first display the Temperature screen, it shows the current
temperature at that time. If you leave the Temperature screen on the
display, temperature measurements are taken once every even
number minute (of the Timekeeping Mode time).
•
Temperature measurements are affected by your body temperature
(while you are wearing the watch), direct sunlight, and moisture. To
achieve a more accurate temperature measurement, remove the
watch from your wrist, place it in a well ventilated location out of direct
sunlight, and wipe off all moisture from the case. It takes
approximately 20 to 30 minutes for the case of the watch to reach the
actual surrounding temperature.
GENERAL GUIDE
Resetting the Seconds Count to Zero
1. In the Timekeeping Mode, press B to display the Date screen.
2. Hold down A until the seconds digits start to flash.
3. Press B to set the seconds count to OO .
• Pressing B while the seconds count is in the range of 30 to 59
resets the seconds to OO and add 1 to the minutes. In the range of
00 to 29, the minutes count is unchanged.
4. Press A to return to the current time screen.
GETTING ACQUAINTED