TrakPower Temperature Gauge with Stopwatch User Manual
Infrared temperature gauge with stopwatch, Special features, Specifi cations

Special Features
● Large, easy-to-read backlit LCD screen
● Built-in stopwatch feature to check lap times
● Soft rubber grips
● Battery level indicator
● Reads temperatures in Fahrenheit (F) or Celsius (C)
● Adjustable Emissivity
● Easy push-button control for setup and measurement
● Auto power-off feature to extend battery life
● Protective belt pouch for easy access and portability
● Compact and lightweight
Specifi cations
● Temperature Reading Range: – 27° to +428°F (– 33° to
+ 220°C)
● Infrared Accuracy: 4°F (2°C) or +/– 2% of reading,
whichever is greater
● Ambient Temperature Operating Range: +14° to +122°F
(–10° to + 50°C)
● Adjustable Emissivity: 0.05 to 1.00 (1.00 default)
● Display Resolution: 0.1° F or C
● Response Time: 1 Second
● Field of View: 1:1 optics ratio
● Battery Life: 960 (15 sec) readings or 1 hour continuous
● Battery Type: CR2032 Lithium (3V)
● Dimensions: 3.4 Ч 1.9 Ч 0.9 inches (85 Ч 48 Ч 23 mm)
● Weight: 1.53 oz (43.6 g)
Infrared Temperature
Gauge with Stopwatch
I N S T R U C T I O N M A N U A L
The TrakPower ITG (Infared Temperature Gauge) is a non-contact infrared temperature gauge with a built-in stopwatch
specifi cally designed for use with R/C engines, batteries, and motors. Simply aim the ITG at the target and press the
MEASURE button to quickly and easily display the surface temperature. The distance to target ratio is 1:1. Therefore, the
temperature gauge should be positioned as close to the target as possible.
Important Precautions
● Electromagnetic/Radio Frequency Interference (EMC/
RFI): Readings may be affected if the unit is operated
within a radio frequency electromagnetic fi eld strength of
approximately 3 volts per meter, but the performance of the
instrument will not be permanently affected. Care should
be taken to keep the ITG at least 6 inches away from R/C
transmitters to avoid radio frequency interference.
● Avoid setting the ITG in direct sunlight which can cause
overheating and erratic temperature readings. Keeping your
ITG in its protective pouch or a pocket will help protect it
from overheating.
● Avoid keeping the ITG too close to objects that continuously
generate high heat (like a hot plate) for long periods of time,
which can cause overheating of the ITG.
● Do not allow water or moisture to come in contact with
the ITG.
● Replace battery ONLY with a CR2032 lithium non-
rechargeable battery.
The ITG Advantage
Nitro engines should last a long time if they are well maintained.
To assist with extending the life of your engine as well as getting
it to perform its best, TrakPower suggests using the ITG to
monitor engine temperatures. With the ITG, you can measure
engine temperatures quickly and easily to ensure you don’t
cause permanent damage to your engine by allowing it to
overheat. In addition, the ITG can assist with the fi ne tuning
of your engine by helping to fi nd the proper temperature
before you start any needle adjustments. Adjusting the needle
settings properly can only be done on an engine that is running
at normal operating temperature. The ITG is also great for
checking lap times with the built-in stopwatch to see if the
adjustments you have made on your engine are paying off
with faster lap times.
Note:
Most two-stroke engines run properly between
200ºF and 270ºF. However, you should consult your engine
manufacturer for the appropriate temperature range for your
specifi c engine.
Warning:
Avoid setting the ITG in direct sunlight which can
cause the ITG to overheat and give erratic temperature
readings. Your ITG should always be stored in its protective
pouch. After the unit has been removed from direct sunlight
and allowed to cool, all functions will return to normal.
Taking Temperature Measurements
Point the ITG at the glow plug by inserting the sensor into
the engine head cavity as far as possible as shown on
page 2. It is best NOT to allow the ITG case to actually
touch the engine head, as this could adversely affect the
accuracy of the temperature readings.
Press and release the MEASURE button to turn on the ITG
and immediately begin measuring temperatures. If you press
and hold down the MEASURE button, the temperature reading
will continuously update until the button is released.
Note:
As shown in the diagram on the following page, the
small digits at the top of the screen update the MAXIMUM
temperature the ITG reads while the MEASURE button is
being pressed. The big digits at the bottom of the screen
show the current temperature reading.
™