Delphi SA10034-11B1 - Manual (Page 12)

Your antenna comes with 10 feet of cable. If that is
not sufficient to locate the antenna where there is a
strong XM signal, you may purchase a 50-foot cable
extension (Delphi model number SA10006) from
your SKYFi retailer. Up to two extensions can be
used together for up to 110 total feet of cable.
Outdoor Installation or Indoor Wall Mounting
For maximum flexibility and convenience, your
XM antenna can also be attached vertically to an
external or internal wall.
1. Holding the antenna up, find a wall location that
provides a strong signal. It is recommended that
you use an extension cord to temporarily locate
your Delphi CD Audio System outdoors while
optimizing the antenna location with the
“Antenna Aiming” screen.
2. Attach four screws to the wall using the screw-
locator pattern in Figure 22. (First, photocopy
the pattern to use as a template.) Use screws
with head sizes small enough to fit in the center
of each of the four holes but large enough not to
pop out of the elongated sections. #4 pan-head
screws (3/8-inch long) are recommended. Leave
1/8 inch of the screw shanks visible between the
heads and the wall.
Figure 22: Screw Locator Pattern
3. Tilt the antenna fully back on its base. Place the
antenna base on the four screw heads with the
antenna pivot at the top, and pull down approxi-
mately 3/8 inch until the base is firmly secured
on the wall. (Note that the XM logo will be
upside down when the antenna is properly
installed.)
4. Tilt the antenna away from the wall/base until
the signal is optimized.
Note: Do not cut the antenna cable and attach alterna-
tive connectors or cable. The cable and connectors
included with your Delphi CD Audio System are
specially chosen to ensure that they will work with
XM’s unique frequency band. Use only an XM-
approved extension kit (Delphi model number
SA10006) with your SKYFi system.
Controlling Volume, Bass, and Treble
Controlling Volume
Use the volume knob on the SKYFi panel or the
Vol+/- keys on the remote control to adjust volume
when playing XM Satellite Radio stations.
If you also use your SKYFi Receiver with a SKYFi
Vehicle Adaptor or Home Adaptor kit, the SKYFi
Receiver will remember the volume level previously
set when connected to the Delphi CD Audio System
and will return to that setting the next time the sys-
tem is used.
Note that the “Line Out” level cannot be reset while
the SKYFi Receiver is in the Delphi CD Audio System
since the volume control should be used to control
the audio output. If the line out setting is adjusted
while the receiver is in the SKYFi Vehicle Cradle or
Home Stand and is later reconnected to the
Delphi CD Audio System, it will automatically
return to the prior setting the next time it is
used in the SKYFi Vehicle Cradle or Home
Stand.
Bass and Treble
In SKYFi mode, bass and treble can be adjusted
by pressing the “Menu” button on the SKYFi
Receiver or remote, selecting “Bass + Treble,”
and then setting these features in the same
manner as other menu functions*.
If the SKYFi Receiver is removed from the
Delphi CD Audio System and used in a vehicle
or home adaptor, the bass and treble settings
on the SKYFi Receiver display will be “flat” or
“zero” since the audio signal will be processed by
the vehicle or home audio system. When the SKYFi
Receiver is returned to its cradle in the Delphi CD
Audio System, it will resume the most recent bass
and treble settings.
*Refer to the SKYFi Operating Guide for more specific information on
operating your SKYFi Receiver.
10
SECT
ION 3
1.4 in (35 mm)
1.6 in (40 mm)