Delphi SA10316 - Manual

1 2 3 4
8 7 6 5
Step 2: Install the vent or swivel mount
You can use either the vent mount or the swivel mount for your
Xpress
RC depending on your particular situation.
Installing the vent mount
1 Locate a vent with horizontal slats sturdy enough
to hold your XM cradle and radio.
2 Adjust the clamps to fit your vent.
3 Snap the mount onto the vent.
To remove, push the mount into the vent, then lift up.
You can adjust this screw
to adjust the tension of the
mount with a screwdriver.
TIP! Always be careful to include enough slack in your cable to accommodate
open doors or trunk lids. Use things typically found around the home, like
electrical tape, to secure cables in areas so that hinges do not pinch the cable
with the door. Hide any excess cable in the trim.
If you placed the XM antenna on the front
of the vehicle, route the cable across the
top of the windshield. Gently pry up the
rubber weather seal and tuck the cable
underneath. Follow the weather seal
down to the door jam. Tuck the cable into
the door jam and up to the dash or under
the carpet to the car cradle as shown.
If you placed the XM antenna on the
rear of the vehicle, route the cable
under the weather seal of the rear
window. Route it into the trunk and
through any existing wire passages or
cargo passages to the rear passenger
compartment. Tuck the cable under the
door jam trim or under the carpet to
the radio as shown.
5-way navigation knob
• Turn the knob to scroll through a list.
• Press the center of the XM button to make a selection.
• Press the edge of the XM button to select display, jump, or .
Toggle right Toggle left Toggle up Toggle down Press center button
(XM button)
Vehicle Installation
Step 1: Mount the XM Antenna
1 Choose the best location for your XM
antenna considering your own
personal situation. Pay particular
attention to any accessories that you
may have like luggage racks and how
frequently you may use them.
The XM antenna contains a strong magnet which
will stick to any metal parts of your vehicle.
Magnet
Xpress RC functions
60-Minute Replay Buttons
Pause and replay up to 60
minutes of live XM broadcast.
Power Button
Display
Customize the way you view
content on the display
Left and Right Arrows
Search for channels by
category.
5-way Navigation
Knob
Previews channels; also selects
various menu options.
Menu
Access advanced features
and configuration options.
XM Button
Confirms selection for
channel and menu items, also
press and hold to GameSelect,
to TuneSelect or to save a song.
Fav
Choose among direct
channel entry, favorite
channels, and SongSaver
mode.
Jump
Switches between
current channel and
previous channel.
Info
Displays either your
personal stock or info
extras information.
Number Keys
Enter a channel
directly, select your
favorite channels, or
access songs saved
in SongSaver.
WARNINGS:
When using this product it is always important to keep your eyes on the road and hands on
the wheel. Not doing so could result in personal injury, death, and/or damage to your Xpress RC
Receiver, accessories, and/or to your vehicle or other property.
Xpress RC should be placed in your vehicle where it will not interfere with the function of
safety features, e.g., deployment of airbags. Failure to correctly place Xpress may result in injury
to you or others if the unit becomes detached during an accident and/or obstructs the deploy-
ment of an airbag.
What’s in the Box?
8
5
2
7
4
1
9
6
3
mute
info menu display
0 jump fav
+
Xpress RC
Car Cradle
Remote Control
XM Car Antenna
Swivel Mount
Swivel Mount
Preparation Kit
Car Power Adapter
Swivel Mount
Vent Mount
Extra Adhesive
Pad
Installing the swivel mount
CAUTION: The adhesive used with the swivel mount may make it difficult to remove. Do not
install this mount on leather surfaces and make sure the air temperature is at least 60°F (15°C).
1 Locate a flat surface for the mount. Make sure there is ample room
for the XM cradle and radio when installed.
2 Clean the surface with the preparation kit and let it dry thoroughly.
3 Peel off the adhesive liner. Position, press, and hold the swivel mount
in place for 30 seconds.
IMPORTANT: Let the adhesive cure for 24 hours before attaching the XM
cradle and radio to the mount.
4 Turn the swivel to accommodate the XM cradle and radio. Adjust the tension via
the center screw.
Step 3: Connect your Xpress
RC
1 Plug the antenna into ANT IN on the cradle.
2 Plug the power adapter into DC IN on the cradle.
3 Plug the audio adapter into AUDIO OUT on the cradle.
• Use the Cassette Adapter if your vehicle has a built-in cassette player.
• Use a mini audio cable (sold separately) if your vehicle has
an audio input jack.
4 Insert the cradle into the mount.
5 Insert your Xpress RC into the cradle.
NOTE: If your car does not contain a cassette player or an audio input, you will need to
use either the XM SureConnect (sold separately) or the FM Direct adapter (sold separately).
To remove, carefully lift the adhesive pad with your fingers or a spoon. Warming
the pad with a hair dryer for several minutes will help soften the adhesive.
You can reinstall the swivel mount using the extra adhesive pad.
ANT IN AUDIO OUT DC IN
XM Antenna
Power Adapter
Cassette Adapter
Xpress RC Car Cradle
Cassett Adaptor
Vent Mount
•
•
Dash
Vent
Dash
Vent
•
•
XM SureConnect (sold separately): You can listen to your Xpress RC through your car
stereo by using Xpress RC ’s built-in FM modulator and the XM SureConnect. Simply find
an unused FM frequency on the stereo and set your Xpress RC to transmit on that same
frequency. Refer to Set the FM frequency page in your user guide for more information.
FM Direct Adapter (sold separately): This option directly connects the Xpress RC to your
car’s audio system and antenna. A professional installation is recommended if you choose
to use this method.