Dialogic Brooktrout 931-103-05 - Manual

Installing the Dialogic®
Brooktrout® TR1034 Analog
PCI Fax Board
Part Number: 931-103-05
The Dialogic® Brooktrout® TR1034 Analog PCI
boards (“TR1034” or “TR1034 fax board(s)”) are
full-sized, single-slot, PCI-bus compatible fax boards.
They provide the following:
Š On-board analog connections
Š V.34 (33.6 Kbps) fax transmission speeds
Š Up to eight fax and voice channels per board
The TR1034 Analog PCI Series fax boards can be
used in either 3.3V or 5V bus (signaling) slots.
You need a voice or fax application to use a
TR1034 Analog board. Dialogic does not provide the
application or a driver for this board. A driver comes
with the application that you purchase.
This installation guide provides information about:
Š System Requirements (including telephone
service)
Š Setting the Module Number
Š Installing the Fax Board
Š Recognizing PCI Slots
Š Connecting the Phone Service
Š Understanding LED Signals
Š Using the Dialogic® Brooktrout®
TR1034 Analog Fax Board
Š Getting Help
System Requirements
This board must be installed in an enclosure that
meets the following specifications:
Š A Pentium or later host processor
Š A PCI bus slot that runs at least 33 MHz and is
32 or 64 bits wide. See
Recognizing PCI Slots for
more information.
Š Temperature: 0 C - 50 C
Š Humidity: 10% - 95% (non-condensing)
Š Power Requirements:
The following is also required:
Š Telephone service: analog interface
Setting the Module Number
Set each board to a unique module number to easily
identify the resources associated with a specific board
in a multi-board system.
Use the SW-1 rotary switch (Figure 1) to set a unique
module number for each Dialogic® Brooktrout® fax
board. See Figure 5 for the switch location. Select a
number from 2 - F on the rotary switch. Settings 0 and
1 are reserved and cannot be used.
Figure 1. Rotary Switch (SW-1)
Installing the Fax Board
To install your fax board:
1. Turn off your PC and remove the cover.
2. If the system has a PCI expansion hold-down bar,
remove it.
3. Locate a free PCI bus slot, remove the slot cover.
4. Carefully align the board with the slot and firmly
seat the board into the slot.
5. Tighten the mounting bracket screw to secure the
board to the chassis.
6. Replace the cover.
7. Turn on your computer.
Note: Dialogic® Brooktrout® fax boards should not be present
in the computer during the installation of any operating
system. The operating system might misinterpret the
board as being some other device, with unpredictable
consequences.
Recognizing PCI Slots
The PCI connectors in the computer chassis usually
appear as white slots. The TR1034 Analog Fax Board
has a PCI board edge connector. It can be inserted into
any of the PCI slots shown in Figure 2.
Figure 2. PCI Slots
Connecting the Phone Service
The appropriate telephone service and hookups must
be installed at your site in order to connect to
telephone service. The following table shows the
channel/connector relationship:
Use the cable supplied with the board. Use the
following instructions to connect your board to
Analog service (POTS [plain old telephone service]):
1.
Plug one end of the cable into the RJ-45
telephone connector on the board.
Connect to Connector A for channels 0-3 or to
Connector B for channels 4-7 (see Figure 4 to
locate connectors).
2. Plug the other end into the wall connector for
your telephone service.
See Figure 3 for pinout details for your board:
Figure 3. Analog Connector Pinouts
Board +5 V +3.3 V +12 V -12 V Total Power
2 chan 0.95A 0A 0A 0A 4.75 W
4 chan 1.0A 0A 0A 0A 5.0 W
8 chan 1.08A 0A 0A 0A 5.4 W
Caution: A small amount of static electricity can
destroy the sensitive components on your board.
To prevent static damage, always connect yourself
to ground using a ground strap before touching a
circuit board. Handle boards only by the edges or
metal mounting brackets and transport boards in
an anti-static bag.
Warning: When installing the board, be sure that
the mounting bracket is securely fastened to the
chassis and the chassis is plugged into a
grounded three prong plug. Improper chassis or
bracket grounding can result in harmful or fatal
electrical shock as well as component damage.
5V 64-Bit Connector
3.3V 32-Bit Connector
Insert the connector into any of these slots.
3.3V 64-Bit Connector
5V 32-Bit Connector
Universal PCI Board Edge Connector
Channel
Number
RJ-45
Connector
Type of
Service
0
1
2
3
4
5
6
7 A
A
A
A
B
B
B
B Analog
Analog
Analog
Analog
Analog
Analog
Analog
Analog
1
2
3
4
5
6
7
8
Pin
Tip 2
Ring 2
Tip 1
Ring 0
Tip 0
Ring 1
Tip 3
Ring 3
Port A
Tip 6
Ring 6
Tip 5
Ring 4
Tip 4
Ring 5
Tip 7
Ring 7
Port B