Denon DN-2100F User Manual

Page 9

ENGLISH

Scratch mode:

Scratching is possible by turning the jog wheel dial. (The

DIGI-S LED flashes.)

A1, A2 buttons

• Press these buttons to set the start point for loop playback

(point A-1 or A-2).

• Press these buttons to use the stutter and hot start

functions.

CUE button

• Pressing the CUE button during play provides a return to the

position at which play was started. Alternately pressing the

PLAY/PAUSE button and the CUE button allows the CD to be

played from the same position any number of times.

• The button is lit RED, when in the standby mode.

• When in the sleep mode, press the CUE or PLAY/PAUSE

buttons to “wake up” and cancel sleep mode.

B-LOOP button

• Press this button to set the end point for loop playback (point

B).

PLAY/PAUSE button (

)

• Use this button to start playback.

• Press once to start playback, once again to set the pause

mode, and once more to resume playback.

• In the brake mode, press this button to brake.

EXIT/RELOOP button

• When this button is pressed during a seamless loop, the

track resumes back to normal play from the B point. (EXIT).

When pressed again, the playback jumps back into your A-B

seamless loop. (RELOOP)

PRESET button

• Press this button once to get into the preset mode. Press it

again to save your changes and to get out of this mode.

Track select knob
(

–

/PUSH ENTER)

• Turn this knob to select the first or next track to be played.

• Turn the knob clockwise by one click to move one track

forward, counterclockwise by one click to move one track

backward.

• When the knob is turned while pressing it down, one click

corresponds to advancing 10 tracks at a time.

• In the preset mode, use this knob to set and enter preset

settings.

Pitch slider

• Use this to adjust the playing speed.

• The playing speed decreases when slid upwards and

increases when slid downwards.

PITCH BEND + button

• The playing speed increases while this button is pressed.

• When the button is released, the playing speed returns to

the previous speed.

PITCH/KEY button

• Press this button to activate the playing speed set with the

Pitch slider. The PITCH LED lights up green.

• When the button is pressed again, the key adjust mode is

turned on and the key remains the same even if the pitch is

changed. (KEY ADJUST) The KEY LED flashes.

• Press the button again to cancel the pitch slider, KEY

ADJUST and return to normal speed.

• Press the button more than 1 second, the fixed pitch mode is

locked and the PITCH LED flashes.

BRAKE button

• Press this button to select the brake and the Platter

Stop/Start mode. (BRAKE/PLAT-S mode).

PITCH BEND – button

• The playing speed decreases while this button is pressed.

• When the button is released, the playing speed returns to

the previous speed.

FL Tube Display

• See page 10.

Continue/Single button (CONT./SINGLE)

• Press this button to switch between the single and

continuous play modes.

• The selected mode is indicated by the SINGLE or CONTINUE

indicators on the display.

• Press this button for over 1 seconds to turn the repeat mode

on and off.

TIME button (4-way)

• Press this to switch the time display between the elapsed

time or remaining time per track or per disc.

Disc tray OPEN/CLOSE button

• Press this button to open and close the disc trays.

• The disc trays are programmed to not open during playback.

Stop playback before pressing this button.

(4) DN-2100F Controller (Rear Panel, RC-48)

Control connector (8pin din)

• Connects between the RC-48 (Remote control unit) and the

DN-2100F (main unit) using the provided control cable.

Connector for signal transfer between remote
control units (EXTENSION JACK)

• For the equipment in the future.

EXTRA REMOTE

• Connect the Denon RC-8001ST.

Connecting the RC-8001ST allows wireless control of the

DN-2100F from the RC-8000.

The DN-2100F can be controlled using the RC-8000 Denon

CD (CD player and CD changer) “PLAY MODE 1/5” system

buttons (except that the power cannot be turned on and off).

The player to be operated can be selected using the

CHANGER 4/5 ZONE1 (CD1) and ZONE2 (CD2) buttons.

(The default is CD1.)

“10 key 2/5” buttons 1 to 4 can be used as buttons A1 and

A2.

1 = CD1 A1 button

2 = CD1 A2 button

3 = CD2 A1 button

4 = CD2 A2 button

Other buttons (5 to RANDOM) cannot be used.

(The RC-8001 charger base stations and RC-8000 remote

control unit are sold separately USA, CANADA only)