Kent Razo E17 - Manual (Page 10)

INSTRUCTIONS FOR USE
8
Razor E17
— 909 6311 000(1)2006-01
MACHINE TRANSPORT/PARKING
To transport/park the machine, proceed as follows.
1.
Turn the brush/pad switch and the vacuum switch (2 and
3, Fig. B) to “0”.
2. Disconnect the power supply cable (21, Fig. C) from the
electrical mains, then wind it round its support.
3. Lift the squeegee by means of the lever (19, Fig. C).
4. Grasp the handlebar (2, Fig. C) and slightly lower it until
the rear wheel (7, Fig. C) comes into contact with the
floor (Fig. D). While holding the machine in this position,
push it to the transport/parking area.
5. After finishing the work, in order not to drag the
brush/pad on the floor and leave wet marks, remove the
brush/pad from the deck by using the release device (for
the procedure, see the After Using The Machine
paragraph), then place it on the support (3, Fig. I).
TANK EMPTYING
An automatic float shut-off system (6, Fig. I) stops the vacuum
system when the recovery water tank (4) is full.
The vacuum system deactivation is signalled by a sudden
increase in the vacuum system motor noise frequency.
When the recovery water tank (4, Fig. I) is full, empty it
according to the following procedure.
Recovery water tank emptying
1. Stop the machine by pressing the brush/pad and
vacuum switches (2 and 3, Fig. B).
2. Disconnect the power supply cable (21, Fig. C) from the
electrical mains, then wind it round its support.
3. Lift the squeegee by means of the lever (19, Fig. C).
4. Drive the machine to the appointed disposal area.
5. Insert the positioning pin (24, Fig. C) and lift the
brush/pad by activating the transport/parking device
(23a).
6. Empty the recovery water tank by means of the drain
hose (16, Fig. C).
Then, rinse the tank with clean water.
Solution tank emptying
7. Carry out steps 1 to 4.
8. Empty the solution tank by means of the drain valve (18,
Fig. C).
Then, rinse the tank with clean water.
AFTER USING THE MACHINE
After scrubbing-drying, before leaving the machine:
1.
Remove the brush/pad-holder as follows:
– Lift the brush/pad, turn the brush/pad switch (2,
Fig. B) to “I” and, after a few seconds, to “0”, thus
releasing the brush/pad-holder.
2. Disconnect the power supply cable (21, Fig. C) from the
electrical mains, then wind it round its support.
3. Empty the tanks (4 and 5, Fig. I) according to the
procedure shown in the previous paragraph.
4. Perform the daily maintenance operations (see the
Maintenance chapter).
5. Store the machine in a clean and dry place, with the
brush/pad and the squeegee lifted or removed.
RECOVERY WATER TANK REMOVAL
To perform check and maintenance operations, it may be
necessary to remove the recovery water tank (1, Fig. H)
according to the following procedure.
1.
Empty the recovery water tank (4, Fig. I) according to the
procedure shown in the relevant paragraph.
2. Drive the machine on a level ground.
3. Make sure that the power supply cable (21, Fig. C) is
disconnected from the electrical mains.
4. Disconnect the vacuum hose (22, Fig. C) from the
squeegee (11).
5. Disconnect the recovery water drain hose (16, Fig. C)
from the bracket (17).
6. Open the cover (6, Fig. C) and apply the cover stand (18,
Fig. I).
7. Grasp the recovery water tank (1, Fig. H) in the area (2)
and slightly raise it.
8. Disconnect the vacuum hose (3, Fig. H) from the tank,
then remove the tank (1) with the hoses (4) and (5).
MACHINE LONG INACTIVITY
If the machine is not going to be used for more than 30 days,
proceed as follows:
1.
Perform the operations described in the After Using The
Machine paragraph.
2. Store the machine in a clean and dry place.
FIRST PERIOD OF USE
After the first period of use (first 8 hours) it is necessary to
check the fixing and connecting parts of the machine for
proper tightening. Check the visible parts for integrity and
leakage.