HITEC Gemini - Manual (Page 25)

25
Parts List - Gemini KIT
Part No. Description Material Dimensions
No. off
1 KIT building instructions Paper, 80 g / m² A4
1 1 Decal sheet Printed self-adhesive film 700 x 1000 mm
2 1 L.H. fuselage shell Moulded Elapor foam Ready made
3 1 R.H. fuselage shell Moulded Elapor foam Ready made
4 1 Front fuselage hatch Moulded Elapor foam Ready made
5 1 Canopy frame Moulded Elapor foam Ready made
6 1 L.H. / R.H. cabane Moulded Elapor foam Ready made
7 1 Cabane centre piece Moulded Elapor foam Ready made
8 1 Bottom wing Moulded Elapor foam Ready made
9 1 L.H. wing strut Moulded Elapor foam Ready made
10 1 R.H. wing strut Moulded Elapor foam Ready made
11 1 Top wing Moulded Elapor foam Ready made
12 1 Tailplane Moulded Elapor foam Ready made
13 1 Fin Moulded Elapor foam Ready made
14 1 Left inner wheel spat Moulded Elapor foam Ready made
15 1 Right inner wheel spat Moulded Elapor foam Ready made
16 1 Left outer wheel spat Moulded Elapor foam Ready made
17 1 Right outer wheel spat Moulded Elapor foam Ready made
18 1 Spinner Moulded Elapor foam Ready made, 62 Ø
19 1 Canopy Vac. moulded plastic Ready made
Small parts set
20
3 Velcro tape, hook Plastic 25 x 60 mm
21 3 Velcro tap, loop Plastic 25 x 60 mm
22 4 Latch catch Injection-moulded plastic Ready made
23 4 Latch tongue Injection-moulded plastic Ready made
24 3 Glue-fitting control surface horn Injection-moulded plastic Ready made
25 6 Swivel pushrod connector Metal Ready made, 6 mm Ø
26 6 Washer Metal M2
27 6 Nut Metal M2
28 8 Socket-head grubscrew Metal M3 x 3 mm
29 1 Allen key Metal 1.5 mm A/F
30 2 Aileron pushrod, one Z-bend Metal 1 Ø x 70 mm
31 2 Wing screw Plastic M5 x 50 mm
32 2 Wing screw support A Injection-moulded plastic Ready made, M5
33 2 Wing screw support B Injection-moulded plastic Ready made, M5
34 2 Glue-fitting sleeve for M5 screw Injection-moulded plastic Ready made
35 4 Glue-fitting link horn, flat, 1.3 Ш + 2.5 Ш Injection-moulded plastic Ready made
36 1 Glue-fitting tailwheel horn Injection-moulded plastic Ready made
37 1 Glue-fitting tailwheel bracket Injection-moulded plastic Ready made
38 1 Spinner holder Injection-moulded plastic Ready made
39 2 Motor mount Injection-moulded plastic Ready made
40 1 Motor bulkhead Injection-moulded plastic Ready made
41 4 Adjustor screw, motor bulkhead mounting Metal M3 x 10 mm
42 2 Motor bulkhead mounting screw Metal M3 x 16 mm
Wire and tube set
50
1 Tubular spar GRP tube 6 Ø x 3.4 Ø x 575 mm
51 2 Steel pushrod, elevator + rudder, one Z-bend Metal 0.8 Ø x 355 mm
52 2 Snake outer sleeve, elevator + rudder Plastic 3 Ø x 2 Ø x 300 mm
53 2 Snake inner sleeve, elevator + rudder Plastic 2 Ø x 1 Ø x 320 mm
54 2 Aileron link pushrod Metal 1.3 Ø x 185 mm
Undercarriage set
60
1 Main undercarriage Spring steel 2.5 Ø, ready made
61 2 Lightweight wheel Plastic, EPP 53 Ø, hub bore 2.6
62 4 Collet Metal 2.7 Ø x 8 Ø x 5 mm
63 2 Socket-head grubscrew Metal M3 x 3 mm
64 2 Socket-head grubscrew Metal M3 x 5 mm
65 2 Wheel spat holder Plastic Ready made
66 1 Undercarriage retainer Plastic Ready made
67 1 Screw Metal M3 x 12 mm
68 1 Tailwheel unit Metal 1.3 mm Ø
69 1 Lightweight tailwheel Foam rubber 26 mm Ø
70 2 Tailwheel retainer (tubular rivet) Metal A2.0 x 0.2 x 3