Custom Autosound Secretaudio SST User Manual

Page 6

Wired Commander Mounting

Wired Commander Bracket Mount
(1) Use the two self tapping screws (T3x12) to mount the Swivel Bracket in place.
(2) Put the two small brackets into the right and left ears of Commander
(3) Put the commander into the swivel bracket and fasten using the large machine

thumb screws.

(1)

(3)

(2)

Wired Commander flush Mount
(1) Find a flat area that is a minimum of 5-3/4” w x 2-3/4” h
(2) Check area behind for any obstructions. Needs a min. of 1” clearance
(3) Cut a 5-1/4” w x 2-1/4 h hole for the flush mount bezel. Cut 1/8”w x 3/4” high
clearance for tabs on side of LCD. (fig.1) Be extremely careful to not cut this
opening oversize or the trim bezel will not cover up the hole. Best to cut the opening
slightly small and then file to fit.
(4) Insert metal bezel into cutout and bend mounting tabs (A) outward to secure it into
the opening. fig. (2)
(5) Place commander into bezel (fig. 3) and press fit plastic trim ring (B) over the
commander. (fig.4)

TUNER OPERATION

Select a Band

Press the BAND button (8) to change between three FM bands and two AM (MW) bands.

Manual Tuning

Press the TUNE/TRK >>| or |<< buttons (2, 3) to seek stations up/down step by step.

Auto Seek Tuning

Press and hold the TUNE/TRK >>| or |<< buttons (2, 3) to automatically seek the next or
previous strong station.

Preset Stations

Six numbered preset buttons store and recall stations for each band.
Store a Station
Select a band (if needed), then select a station. Press and hold a preset button (10-15) for
two seconds. The preset number will appear in the display.
Recall a Station
Select a band (if needed). Press a preset button (10-15) to select the corresponding
stored station.

Automatically Store / Preset Scan (AS/PS)

Automatically Store
Select a band (if needed). Press and hold the AS/PS (7) button for more than three sec-
onds to automatically select six strong stations and store them in the current band. The
new stations replace any stations already stored in that band.
Preset Scan
Select a band (if needed). Press AS/PS (7) to scan stations stored in the current band.
The unit will pause for ten seconds at each preset station. Press AS/PS again to stop
scanning when the desired station is reached.

CD Changer Mode (For Optional CD Changer)
Selecting a Disc DN(14) UP(15)
To slect a disc, press DN(14) or UP(15) until the desired disc number is show-
ing on the LCD display
Selecting Tracks >>(2) <<(3)
-Press the button >>(2) or <<(3) to skip to next track or last track on the CD.
-Press and hold the button >>(2) or <<(3) to fast forward or fast reverse through
the disc. CD play starts when the button is released.
Play/Pause Disc playback 1 >/II(10)
Press button 1 >/II(10) to pause disc play, press this button again to resume
disc play.
Previewing Tracks (11)
Press the 2 INT button (11) to play only first 10 seconds of each track in the
current disc repeately. Press this button again to stop intro scan and resume
normal play at the current track.
Repeat Play (12)
Press the 3 RPT button (12) during disc play to repeat play the current track,
press this button again to stop repeat play.
Long press this button (12) to repeat play all the tracks on current CD.
Random Play (13)
Press 4/RDM button (13) during disc play to play all tracks on a CD in random
order. Press this button again to stop random play. Long press this button (13)
to random all the tracks on the CD changer.

fig. (1)

fig. (2)

fig. (3)

fig. (4)