Denon DN-C635 - Manual (Page 9)

9
ENGLISH
✽. This operation only works while the power is on.
1. Press the power operation switch q to turn on the power.
2. Press the OPEN/CLOSE button e.
4 OPENING AND CLOSING THE DISC HOLDER AND
LOADING A DISC
Opening and closing the disc holder
• Make sure the disc holder is completely open.
• Hold the disc by the edges and place it on the disc
tray. (Do not touch the signal surface, i.e., the
glossy side.)
• When using 12 cm. diameter discs, make sure the
outer edge matches the tray guide circumference
and when using CD signals (8 cm. diameter) match
the outer edge with the inner tray guide
circumference.
• Press the OPEN/CLOSE button e to close the disc
holder w.
• When the disc holder is open and a disc is loaded,
you may also press the PLAY ( 1 ) button y to close
the disc holder. (If the PLAY ( 1 ) button is pressed,
playback will start immediately upon the disc
contents having been read.)
How to load a disc
CAUTIONS:
• If you finger should get caught in the disc
holder when it closes, press the OPEN/CLOSE
button.
• Do not place any foreign objects on the disc
tray, and do not place more than one disc on the
tray at a time. Otherwise malfunction may
occur.
• Do not push in the disc tray manually when the
power is off as this may cause malfunction and
damage the CD player.
• This player can play CD-R/RW discs, but only if
they are finalized. Note however that depending
on the recording quality, the player may not be
able to play some finalized CD-R/RW discs.
2 Messages
Messages may appear on the display while using the DN-C635. The meanings of these messages are
explained below.
Message Meaning
No Disc No disc inserted, disc unreadable or disc inserted upside down.
TOC Error The disc information has not been read properly.
Invalid CD The disc is a CD-ROM that does not contain MP3 files.
Tray Error The disc holder could not be opened or closed properly.
5 NORMAL CD PLAYBACK
1. Press the power operation switch q to turn on the
power.
2. Load the disc you want to play.
3. Make the presettings according to the usage
purpose. (See page 14.)
• Select the play finish mode. (Preset functions)
Finish stop :
The stop mode (the servo functions turn off) is
set when playback finishes.
Finish next :
The standby mode is set at the beginning of the
next track when playback is finished.
✽ After the final track is played, the standby
mode is set at the beginning of the first track.
Finish recue :
When playback is finished, the standby mode is
set at the position at which playback was started.
• To standby at the point where the sound begins.
(Preset functions)
Set the “C Det” level.
When a track is selected, the position at which
the sound begins is found when a track is cued
and the standby mode is set at that point.
• Press the PLAY MODE button !3 to select the
play mode.
SINGLE : (single track play mode)
The stop mode is set after the specified track is
played.
CONT. : (continuous play mode)
The stop mode is set after the last track is
played.
4. Press the PLAY ( 1 ) button y.
(1) Starting playback
Playback can be temporarily halted and then continued
from the same point in the track.
1. Press the PAUSE ( 3 ) button i during playback.
2. To continue playback, press the PLAY ( 1 ) button y.
(2) Pausing playback at any point
(Pause)
Sleep mode (Preset functions)
• The sleep mode is set if no operation is
performed for set-up time in the standby, pause
or manual search mode.
When in the sleep mode, if the PLAY button is
pressed, playback will be started from the
beginning of the track in which the sleep mode
was set. If the CUE button is pressed, it will
standby for the beginning of the track in which
the sleep mode was set.
1. Press the STOP ( 2 ) button u.
(4) Stopping playback
When the CUE button r is pressed during the play
mode, the pickup returns to the position at which
playback started and the pause mode is set.
(3) Returning to the position at which
playback started
(Back Cue)
Press the
1 button
Play internal Play internal
Press the
3 button
Press the
CUE button
Press the 1 button
Back cue operation
Position
on the
disc