Virtual tach system, Multi-speed tach programming, Horn honk timing – Autostart AS-1755V User Manual

Page 3: Supplementary information fifth relay output

Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".

Virtual Tach System

• Virtual Tach System combines the latest microcontroller technology and a complex algorithm that took years to develop. VTS

is able to effectively monitor the engine starting sequence and release the starter at the right time without physically connecting

the tach wire to the remote starter. The VTS constantly monitors the data and readjusts itself automatically in order to maximize

its capability to start the engine properly in any weather or deteriorating battery condition (automatic transmission only).

Optional Time Delay Adjustment in Virtual Tach System

Follow these steps to program crank time adjustment, if needed:

1. Flash the hood pin (see p.1) — the parking lights will stay on for up to 20 seconds.

Before the lights go out, press and hold the brake pedal and press the

lock

and

unlock

buttons simultaneously — the

parking lights will flash 4 times. Do not release the brake pedal.

3. Press the

lock

button if you wish to increase the time delay or the

unlock

button if you want to decrease it. The time

delay will be increased or decreased by 50ms. and the parking lights will flash once every time the

lock

unlock

button is pressed.

4. Press the

trunk

button to save the settings you have entered.

5. Release the brake pedal - the time delay programming is now complete.

Multi-speed Tach Programming

1. Flash the hood pin (see on page 1) — the parking lights will stay on for up to 20 seconds.

Before the lights go out, press and hold the brake pedal and press the

lock

and

unlock

buttons simultaneously — the

parking lights will flash 4 times. At that point, release the brake pedal.

3. Start up the engine and allow the vehicle to reach regular engine idle speed.

4. Once the engine is running at normal idle speed, press the brake pedal and keep it down until you hear the parking lights

output click 5 times.

5. Release the brake pedal —^the tach programming is now complete.

Horn Honk Timing

Follow these steps to program horn confirmation:

1. Ensure that the hood is up and that the ignition is off.

•

Hold the hood pin down for 4 seconds.

•

Release the hood pin. The parking lights will come on.

•

While the parking lights are on, immediately push and release the hood pin again. — The parking lights will stay on for up to

20 seconds.

2. Press and hold the brake pedal, then simultaneously press the

unlock

and

start

buttons — the horn will chirp 5 times.

3. Release the brake pedal.

4. To change the timing:

To increase the Horn pulse by 3 ms, press the

lock

button.

To decrease the pulse by 3 ms, press the

unlock

button.

To increase the pulse by 10 ms, press the

start

button.

To decrease the pulse by 10 ms, press the

trunk

button.

5. To save the new settings: press

lock

and

unlock

. If 3 chirps are returned, the new settings have been saved.

Supplementary Information

Fifth Relay Output

(2nd IGN, ACC or CRANK)

Remote car starters of this series are equipped with an on-board high

current programmable 5

relay that can be used to power a second

ignition, accessory or crank wire. The unit uses 3 sets of pins; each set

corresponds to a specific function of the output. In order to activate one of

the three possible functions, you must place the jumper (supplied) on one

of the three sets of pins and connect the 14 AWG wire to the second IGN. /

ACC. /

crank

wire of the vehicle.

Caution!

Only one set of pins can be used at one time. Using more than one jumper may result in serious damage to the vehicle. The

relay output rating on this unit is 25a at most. Defective oem solenoid switches can sometimes draw up to 50 or 60a, causing

the 30a fuse to blow. Always verify your circuit with an appropriate measuring device.

http://www.autostart.ca

Installation Guide

mode

indicates

default

setting

function

1 - Safe Start

OPTION 1

Safe Start

enabled

option

Safe Start

disabled

OPTION 3 “Swap Start” - enhanced safe start mode with extended safety: To start the engine: press

the

lock

and

unlock

buttons simultaneously. To trigger

aux

: press

start

button.

function

2 - Engine Run Time

OPTION 1

Run Time = 3 minutes in gas mode / 8 minutes diesel mode

option

Run Time = 15 minutes in gas mode / 20 minutes diesel mode

OPTION 3 Run Time = 25 minutes in gas mode / 30 minutes diesel mode

function

3 - Idle Mode & Turbo Mode (auto) / Turbo Mode (manual)

OPTION 1

Idle mode & turbo mode

disabled

(AUTO)

turbo mode

disabled

(

manual

)

option

Idle mode & turbo mode

enabled

(AUTO)

turbo mode

disabled

(

manual

)

OPTION 3 Idle mode & turbo mode

enabled

(AUTO)

/ turbo mode

enabled

(

manual

)

function

4 - Engine type and Cold Weather Mode

OPTION 1 Diesel mode with 20-minute run time in cold weather mode (30-sec. wait to start delay)

option

2* Gas mode with 3-minute run time in cold weather mode

OPTION 3

Diesel mode with 8-minute run time in cold weather mode (18-sec. wait to start delay)

OPTION 4

Diesel mode with 8-minute run time in cold weather mode (7-sec. wait to start delay)

function

5 - Ignition Valet

OPTION 1

Ignition valet

disabled

option

Ignition valet

enabled

mode

* INDICATES DEFAULT SETTING

function

1 - Home Valet

OPTION 1

Home valet

enabled

option

Home valet

disabled

function

2 -

aux

1 Programming

OPTION 1 Horn confirmation upon the 2

press of the

lock

button.

option

Priority door access

OPTION 3 Horn confirmation upon the 1

press of the

lock

button.

function

3 -

aux

2 Programming

OPTION 1 Constant output by pressing

lock

and

unlock

buttons simultaneously

In safe start mode: activate

aux

by pressing the

start

button.

OPTION 2*

Toggle ON/OFF (with 30-second time out)

OPTION 3

Toggle

ON/OFF

(with 4-minute time out) ^active when under remote run

OPTION 4

Priority door access

function

4 -

aux

3 / Zone 3 Programming

OPTION 1

1-sec. output when

trunk

button is pressed for 3 sec. with ignition off or under remote run

option

Constant output while the

trunk

button is pressed

OPTION 3

Trunk output with disarm and rearm pulses

function

5 - External Trigger

OPTION 1 Zone 3 disarm/rearm (trunk pin: a disarm pulse is sent before the trunk opens; the vehicle

rearms 4 seconds after the trunk is closed)

option

Engine start / stop

OPTION 3

Key sense

OPTION 4

Pager

mode

* INDICATES DEFAULT SETTING

function

1 - Alarm Control

OPTION 1

enabled

(

horn

must be enabled)

option

disabled

function

2 - Remote Options

OPTION 1

generation remote (with

STOP

button)

option

generation remote. Press

AUX

for less than 3 sec. = Stop

Press

aux

for more than 3 sec. = Panic

function

3 - Ready Mode Option

OPTION 1

Enabled by handbrake

option

Enabled by remote

Installation Guide

http://www.autostart.ca/

P. 6

P. 3