ADC AD-78 User Manual
Ad-78, Installation manual
Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".
AD-78
(Gas/Electric/Steam)
Installation Manual
WARNING; For your safety the information in this manual must
be followed to minimize the risk of fire or explosion
or to prevent property damage, personal injury or loss
of life.
Do not store or use gasoline or other flammable vapor
and liquids in the vicinity of this or any other
appliance.
WHAT DO YOU DO IF YOU SMELL GAS
*
*
Do not try to light any appliance.
Do not touch any electrical switch; do not use any phone in
your building.
Clear the room, building or area of all occupants.
Immediately call your gas supplier from a neighbor's phone.
Follow the gas supplier's instructions.
If you cannot reach your gas supplier, call the fire
department.
Installation and service must be performed by a qualified installer,
service agency or the gas supplier.
For replacement parts, contact the distributor from which the dryer
was purchased or
American Dryer Corporation
88 Currant Road
Fall River MA 02720-4781
Telephone; (508) 678-9010 / Fax: (508) 678-9447
E-mail: [email protected]
080197JEV/abe
ADC
Part No. 113023
Document Outline
- Retain This Manual In A Safe Place For Future Reference
- Important
- IMPORTANT
- CAUTION
- WARNING
- WARNING
- FOR YOUR SAFETY
- IMPORTANT
- Table of Contents
- Specifications*
- B. COMPONENT IDENTIFICATION
- SECTION III
- INSTALLATION PROCRDURES
- A. LOCATION REQUIREMENTS
- B. UNPACKING/SETTING UP
- C. DRYER ENCLOSURE REQUIREMENTS
- D. FRESH AIR SUPPLY
- E. EXHAUST REQUIREMENTS
- R ELECTRICAL INFORMATION
- I. PREPARATION FOR OPERATION/START-UP
- J. PREOPERATIONAL TESTS
- K. PREOPERATIONAL INSTRUCTIONS
- L. SHUT DOWN INSTRUCTIONS
- A. SERVICE
- B. PARTS
- A. SERVICE
- B. PARTS
- A. RETURNING WARRANTY CARPrS^
- B. PARTS
- C. RETURNING WARRANTY PARTS
- INSTALLATION PROCRDURES
- SECTION VI
- ROUTINE MAINTENANCE
- TROUBLESHOOTING
- A. No L.E.D. (light emitting diode) display (for microprocessor [computer] models ONLY)...
- B. Drive motor |s operating (does not start)...
- C. Drive motor (Reversing Models ONLY) operates in one direction only ... stops and restarts in the same direction •••
- D. Drive motor operates okav for a few minutes, then stops and will not restart...
- O. Microprocessor controller (computer) locks up and L.E.D. (light emitting diode) display reads erroneous message(s) or only partial segments...
- P. Dryer stops during a cycle, microprocessor controller (computer) buzzer (tone) sounds for 5 seconds, and then the L.E.D. display reads “dSFL” for approximately 30 seconds, and then returns to “FILL”...
- Q. Dryer stops during a cycle, microprocessor controller (computer) buzzer (tone) sounds for 5 seconds, and then the L.E.D. returns to “FILL”...
- R. Microprocessor controller (computer) L.E.D. display reads “SEFL”...
- S. Microprocessor controller (computer) L.E.D. display reads “Hot”...
- W. Dryer operates but is taking too iong to dry...
- X. At the completion of the "AUTO" drying/cooling cycle, the load is coming out over dried...
- Y. At the completion of the "AUTO" drying/cooling cycle, the load is coming out still damp...
- Z. Main burners are burning with a yellow flame (for Gas Models ONLY)...
- AA. Condensation on main door glass...
- BB. Scraping noise at basket (tumbler) area...
- CC. Excessive noise and/or vibration...
- A. Dryer will not start...both drive motor and blower (impellor/fan) motor are not operating and indicator light h off...
- B. Drive motor is not operating (does not start)...
- C. Drive motor (Reversing Models ONLY) operates in one direction only... stops and restarts in the same direction...
- D. Drive motor operates okay for a few minutes, then stops and will not restart...
- E. Blower/Fan motor is not operating (does not start)...
- E Blower/Fan motor operates okay for a few minutes, then stops and MU not restart...
- G. Both drive motor and hlower (impellor/fan) motor (Reversing Models ONLY) not operating (do not start) and indicator light is on...
- H. Heating unit is not operating (no heat)...no voltage at heating unit (i.e.. Gas Model > Hot Surface Ignition [HSI] module. Electric Model - electric oven contactor, or Steam Model - steam damper system pneumatic solenoid) when dryer is first started...
- I. № heat)...no voltage at heating unit (i.e., Gas Model - Hot Surface Ignition [HSI] module, Electric Model - electric oven contactor, or Steam Model - steam damper system pneumatic solenoid) •••
- J. Dryer operates but is taking too long to dry...
- K. Main burners are burning with a yellow flame (for Gas Models ONLY)...
- L. Condensation on main door glass...
- M. Scraping noise at basket (tumbler) area...
- N. Excessive noise and/or vibration...
- SECTION VIII
- SECTION IX